IDES Prospector Already have an account? Login Here

IDES

Asahi Kasei ABS B-20FG-1121

Acrylonitrile Butadiene Styrene

Glass Fiber Reinforcement, 20%

Supplied by Asahi Kasei Plastics North America Inc.

The technical datasheet with complete property values for Asahi Kasei ABS B-20FG-1121 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 20% Filler by Weight
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (230°C/3.8 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Unnotched Izod Impact
ft·lb/in
 ASTM D4812
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
Related Terminology
This supplier and product may also be known by these terms: Thermofil, Asahi Thermofil

Product names can be difficult to match. You may have searched any one of these terms to find this product: Asahi Kasei ABS B-20FG-1121, Asahi Kasei ABS B20FG1121, Asahi Kasei ABS , AsahiKaseiABSB20FG1121, AsahiKaseiABS, ABSB 20 FG 1121, ABSB-20FG-1121, ABSB20FG1121, ABSB:20FG:1121, ABSB/20FG/1121, ABSB+20FG+1121, ABSB_20FG_1121, ABSB 20FG 1121, ABSB20, ABSB, B 20 FG 1121, B-20FG-1121, B20FG1121, B:20FG:1121, B/20FG/1121, B+20FG+1121, B_20FG_1121, B 20FG 1121, B20, 20FG, FG1121, Acrylonitrile Butadiene Styrene, ABS, Asahi Kasei NA, AcrylonitrileButadieneStyrene, 20B, 20ABSB
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Holding Pressure
psi
  
Back Pressure
psi
  
Injection Notes
Screw Rpm: Normal
Cooling Time: Short
Screw Type: General
Slightly longer cycle times may be required to mold wall thicknesses over 1/4 inch.
Slightly higher injection pressures and mold temperatures may be required to mold wall thicknesses below 0.100 inches (2.54 mm).
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.