IDES Prospector Already have an account? Login Here

IDES

Pebax® 5533 SA 01

Polyether Block Amide

Supplied by Arkema

The technical datasheet with complete property values for Pebax® 5533 SA 01 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Features 
  • Good Mold Release
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Injection Molding
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (235°C/1.0 kg)
g/10 min
 ASTM D1238
Water Absorption
     ASTM D570
24 hr
%
  
Saturation
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
     ASTM D638
Yield
psi
  
Break
psi
  
Tensile Elongation
     ASTM D638
Yield
%
  
Break
%
  
Flexural Modulus
psi
 ASTM D790
Flexural Strength (Yield)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
     ASTM D256
-40°F
 
  
66°F
 
  
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ASTM D1525
Melting Temperature
°F
  
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Constant (1 kHz)
 
 ASTM D150
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Pebax® 5533 SA 01, Pebax 5533 SA 01, Pebax® , Pebax, Pebax5533SA01, 5533 SA 01, 5533SA, SA01, 5533SA01, Polyether Block Amide, PEBA-Ether, PEBAEther, PEBA:Ether, PEBA/Ether, PEBA+Ether, PEBA_Ether, PEBA Ether, Thermoplastic Elastomer, TPE, Arkema, PolyetherBlockAmide, ThermoplasticElastomer, SA5533
Features
Features may also be described by the following terms: Good Mold Release, Easy Release, Good Demolding.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Suggested Max Regrind
%
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Back Pressure
psi
  
Screw Speed
rpm
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.