IDES Prospector Already have an account? Login Here

IDES

Plenco 01506 (Injection)

Thermoset Polyester

Cellulose Filler; Glass Fiber Reinforcement; Mineral Filler

Supplied by Plastics Engineering Co.

The technical datasheet with complete property values for Plenco 01506 (Injection) is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
PLENCO 01506 is a mineral and cellulose filled granular polyester molding compound, with glass fiber reinforcement for improved mechanical strength properties. 01506 offers excellent electrical properties and resistance to chemical degradation from repeated detergent exposure. UL recognized under component file E40654. 01506 is available in beige.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Cellulose Filler
  • Glass Fiber Reinforcement
  • Mineral Filler
Features 
  • Detergent Resistant
  • Good Chemical Resistance
  • Good Electrical Properties
  • Good Strength
  • Low Shrinkage
Appearance 
  • Beige
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Apparent Density
g/cm³
 ASTM D1895
Molding Shrinkage - Flow
     ASTM D6289
--
in/in
  
248°F, 72 hr
in/in
  
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Compressive Strength
psi
 ASTM D695
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
ft·lb/in
 ASTM D256
Notched Izod Impact
ft·lb/in
 ASTM D256
Drop Ball Impact
ft·lb/in
 Internal Method
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (E-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
Max. Continuous Use Temperature
°F
 ASTM D794
CLTE - Flow
in/in/°F
 ASTM E831
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength 2
V/mil
 ASTM D149
Dielectric Constant (1 MHz)
 
 ASTM D150
Dissipation Factor (1 MHz)
 
 ASTM D150
Arc Resistance
sec
 ASTM D495
Comparative Tracking Index
V
 ASTM D3638
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.118 in)
 
 UL 94
Oxygen Index
%
 ASTM D2863
UL File Number
 
  
Related Terminology
This supplier and product may also be known by these terms: Plenco

Product names can be difficult to match. You may have searched any one of these terms to find this product: Plenco 01506, Plenco 01506 (Injection), Plenco 01506 Injection, Plenco , Plenco01506Injection, 01506, 01506 (Injection), 01506 Injection, 01506Injection, Polyester, Thermoset, Polyester Thermoset, Polyester, TS, Polyester TS, Thermoset, TS, Plastics Eng, PolyesterThermoset, PolyesterTS, Injection01506
Features
Features may also be described by the following terms: Good Electrical Properties, Detergent Resistant, Detergent Resistance, Good Chemical Resistance, Chemical Resistant, Good Strength, Low Shrinkage.
Injection
Nominal Value
Unit
 
Suggested Shot Size
%
  
Rear Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Back Pressure
psi
  
Screw Speed
rpm
  
Cushion
in
  
Injection Notes
Injection Time: 3-6 sec
Notes
1Typical properties: these are not to be construed as specifications.
2Method A (Short-Time)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.