IDES Prospector Already have an account? Login Here

IDES

LEMALLOY® C61HL

Polyphenylene Ether + PS + Nylon

Supplied by Mitsubishi Engineering-Plastics Corp

The technical datasheet with complete property values for LEMALLOY® C61HL is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • North America
Physical
Dry
Conditioned
Unit
Test Method
Density
--
g/cm³
 ISO 1183
Melt Volume-Flow Rate (MVR) (280°C/5.0 kg)
--
in³/10min
 ISO 1133
Molding Shrinkage
        
Across Flow: 0.126 in
--
%
  
Flow: 0.126 in
--
%
  
Mechanical
Dry
Conditioned
Unit
Test Method
Tensile Modulus (73°F)
psi
 ISO 527-2
Tensile Stress (Yield, 73°F)
psi
 ISO 527-2
Tensile Strain (Yield, 73°F)
%
 ISO 527-2
Nominal Tensile Strain at Break (73°F)
%
 ISO 527-2
Flexural Modulus (73°F)
psi
 ISO 178
Flexural Strength (73°F)
psi
 ISO 178
Impact
Dry
Conditioned
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179
Charpy Unnotched Impact Strength (73°F)
 
 ISO 179
Thermal
Dry
Conditioned
Unit
Test Method
Heat Deflection Temperature
        
66 psi, Unannealed
--
°F
 ISO 75-2/B
264 psi, Unannealed
--
°F
 ISO 75-2/A
CLTE - Flow
--
in/in/°F
 ISO 11359-2
Electrical
Dry
Conditioned
Unit
Test Method
Surface Resistivity
--
ohms
 IEC 60093
Volume Resistivity
--
ohm·cm
 IEC 60093
Relative Permittivity
       IEC 60250
100 Hz
--
 
  
1 MHz
--
 
  
Dissipation Factor
       IEC 60250
100 Hz
--
 
  
1 MHz
--
 
  
Electric Strength
       IEC 60243-1
0.0394 in
--
V/mil
  
0.118 in
--
V/mil
  
Related Terminology
Dry
Product names can be difficult to match. You may have searched any one of these terms to find this product: LEMALLOY® C61HL, LEMALLOY C61HL, LEMALLOY® , LEMALLOY, LEMALLOYC61HL, C 61 HL, C61HL, C61, 61HL, Polyphenylene Ether + PS + Nylon, Polyphenylene Ether PS Nylon, Polyphenylene Ether : PS : Nylon, Polyphenylene Ether / PS / Nylon, Polyphenylene Ether - PS - Nylon, Polyphenylene Ether _ PS _ Nylon, Polyphenylene Ether PS Nylon, PPE+PS+Nylon, PPEPSNylon, PPE:PS:Nylon, PPE/PS/Nylon, PPE-PS-Nylon, PPE_PS_Nylon, PPE PS Nylon, Polyphenylene Ether, PPE, Mitsubishi EP, PolyphenyleneEtherPSNylon, PolyphenyleneEther, PolyphenyleneEther_PS_Nylon, 61C
Conditioned
Product names can be difficult to match. You may have searched any one of these terms to find this product: LEMALLOY® C61HL, LEMALLOY C61HL, LEMALLOY® , LEMALLOY, LEMALLOYC61HL, C 61 HL, C61HL, C61, 61HL, Polyphenylene Ether + PS + Nylon, Polyphenylene Ether PS Nylon, Polyphenylene Ether : PS : Nylon, Polyphenylene Ether / PS / Nylon, Polyphenylene Ether - PS - Nylon, Polyphenylene Ether _ PS _ Nylon, Polyphenylene Ether PS Nylon, PPE+PS+Nylon, PPEPSNylon, PPE:PS:Nylon, PPE/PS/Nylon, PPE-PS-Nylon, PPE_PS_Nylon, PPE PS Nylon, Polyphenylene Ether, PPE, Mitsubishi EP, PolyphenyleneEtherPSNylon, PolyphenyleneEther, PolyphenyleneEther_PS_Nylon, 61C
Injection
Dry
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Screw Speed
rpm
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.