IDES Prospector Already have an account? Login Here

IDES

TAROMID A 280 Z1 G6

Polyamide 66

Glass Fiber Reinforcement, 30%

Supplied by Taro Plast S.p.A.

The technical datasheet with complete property values for TAROMID A 280 Z1 G6 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Polyamide 66 medium viscosity 30% glass fibres reinforced, elastomer modified, very good mechanical properties, good dimensional stability and low water absorption.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 30% Filler by Weight
Additive 
  • Impact Modifier
Features 
  • Good Dimensional Stability
  • Impact Modified
  • Low to No Water Absorption
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (280°C/2.16 kg)
g/10 min
 ISO 1133
Molding Shrinkage - Flow
%
 Internal Method
Water Absorption
     ISO 62
73°F, 24 hr
%
  
Saturation, 73°F
%
  
Granule Humidity 2
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1
Tensile Stress (Break)
psi
 ISO 527-2/50
Tensile Strain (Break)
%
 ISO 527-2/50
Flexural Modulus 3
psi
 ISO 178
Flexural Strength 3
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-13°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Notched Izod Impact
     ASTM D256
-4°F
ft·lb/in
  
73°F
ft·lb/in
  
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature 4 (264 psi, Unannealed)
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B50
Ball Pressure Test (401°F)
 
 IEC 60695-10-2
Melting Temperature
°F
 ISO 11357-3
CLTE - Flow (-22 to 86°F)
in/in/°F
 ISO 11359-2
Continuous Use Temperature
     IEC 60216
20000 hr  5
°F
  
Short Term  6
°F
  
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 IEC 60093
Comparative Tracking Index (Solution A)
V
 IEC 60112
Electric Strength (0.0787 in)
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0382 in)
 
 UL 94
Glow Wire Flammability Index (0.0787 in)
°F
 IEC 60695-2-12
Additional Information
Nominal Value
Unit
Test Method
Reinforcement Content 7 (1382°F)
%
 ISO 3451
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: TAROMID A 280 Z1 G6, TAROMID A , TAROMIDA280Z1G6, TAROMIDA, A 280 Z 1 G 6, A280 Z1 G6, A280, 280 Z 1 G 6, A280Z1G6, 280 Z1 G6, 280Z, Z1, 1G, G6, 280Z1G6, Polyamide 66, Nylon 66, Polyamide, Nylon, pa66, Taro Plast, Polyamide66, Nylon66, Z280, 280A
Generic Name
Generic Name may also be described by the following terms: PA66.
Features
Features may also be described by the following terms: Good Dimensional Stability, Dimensionally Stable, Low Water Absorption, Low Moisture Absorption, Water Resistant, Moisure Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Injection Notes
Pre-heat Temperature: 80 to 100°C
Pre-heat Time: 3 hr
Notes
1Typical properties: these are not to be construed as specifications.
2TARO 002
30.039 in/min
4120°C/hr
5H 130
6H 180
71 hr
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.