TAROMID A 260 Y0 Taro Plast Polyamide 66/6 Copolymer

Product Description

PA66/6 medium viscosity, flame retarded V0 halogen and phosphorus free. Low density, good flow and high tracking resistance.

UL94 V0 listed all colors at 0,55 mm

Available: different colors.

General

Material Status

Commercial: Active

Availability

Europe

Features

Flame Retardant

Good Flow

Halogen Free

Low (to None) Phosphorus Content

Low Density

Medium Viscosity

Tracking Resistant

Appearance

Colors Available

Forms

Pellets

Processing Method

Injection Molding

Physical	Nominal Value	Unit	Test Method
Specific Gravity
--			ASTM D792
--		g/cm³	ISO 1183
Molding Shrinkage			ASTM D955
Flow		in/in
Across Flow		in/in
Water Absorption
73°F, 24 hr		%	ASTM D570, ISO 62
Saturation		%	ASTM D570
Saturation, 73°F		%	ISO 62
Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus		psi	ASTM D638, ISO 527-2
Tensile Strength			ASTM D638, ISO 527-2
Yield		psi
Break		psi
Tensile Elongation (Break)		%	ASTM D638, ISO 527-2
Flexural Modulus		psi	ASTM D790, ISO 178
Flexural Strength
--		psi	ISO 178
Break		psi	ASTM D790
Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength² (73°F)		ft·lb/in²	ASTM D256, ISO 179
Charpy Unnotched Impact Strength² (73°F)		ft·lb/in²	ASTM D256, ISO 179
Notched Izod Impact			ASTM D256
-4°F, 0.126 in		ft·lb/in	ISO 180
73°F, 0.126 in		ft·lb/in	ISO 121
Thermal	Nominal Value	Unit	Test Method
Deflection Temperature Under Load
66 psi, Unannealed		°F	ASTM D648, ISO 75-2/B
264 psi, Unannealed		°F	ASTM D648, ISO 75-2/A
Max. Continuous Use Temperature			IEC 60216
--³		°F
--⁴		°F
Vicat Softening Temperature
--		°F	ASTM D1525⁵, ISO 306/A⁵
--		°F	ASTM D1525⁶, ISO 306/B⁶
Melting Temperature		°F	ASTM D211, ISO 121
CLTE - Flow (-22 to 86°F)		in/in/°F	ASTM D696
Electrical	Nominal Value	Unit	Test Method
Volume Resistivity		ohm·cm	ASTM D257
Comparative Tracking Index (Solution A)		V	IEC 60112
Flammability	Nominal Value	Unit	Test Method
Flame Rating - UL			UL 94
0.0217 in
0.0630 in
0.126 in
Glow Wire Flammability Index (0.0472 in)		°F	IEC 60695-2-12
Glow Wire Ignition Temperature (0.0472 in)		°F	IEC 60695-2-13
Oxygen Index		%	ASTM D2863
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: TAROMID A 260 Y0, TAROMID A , TAROMIDA260Y0, TAROMIDA, A 260 Y 0, A260 Y0, A260, 260 Y 0, A260Y0, 260 Y0, 260Y, Y0, 260Y0, Polyamide 66/6 Copolymer, Polyamide 666 Copolymer, Polyamide 66:6 Copolymer, Polyamide 66+6 Copolymer, Polyamide 66-6 Copolymer, Polyamide 66_6 Copolymer, Polyamide 66 6 Copolymer, Nylon 66/6, Nylon 666, Nylon 66:6, Nylon 66+6, Nylon 66-6, Nylon 66_6, Nylon 66 6, Polyamide, Nylon, pa666, Taro Plast, Polyamide666Copolymer, Nylon666, Polyamide66_6Copolymer, Nylon66_6, Y260, 260A
Generic Name
Generic Name may also be described by the following terms: PA666, PA66/6.
Features
Features may also be described by the following terms: Medium Viscosity, Zero Halogen Content, Halogen Free, Low Phosphorus Content, Low Density, Low Specific Gravity, Good Flow.

Injection	Nominal Value	Unit
Drying Temperature
--		°F
Pre-heater		°F
Drying Time
--		hr
Pre-heater		hr
Processing (Melt) Temp		°F
Mold Temperature		°F
Injection Rate

Notes

¹Typical properties: these are not to be construed as specifications.

²6x4x50 mm

³20000 hrs

⁴Heat Stabilized, 20000 hrs

⁵Loading 1 (10 N)

⁶Loading 2 (50 N)

TAROMID A 260 Y0

Polyamide 66/6 Copolymer

Supplied by Taro Plast S.p.A.