IDES Prospector Already have an account? Login Here

IDES

TAROMID B 280 Z3

Polyamide 6

Supplied by Taro Plast S.p.A.

The technical datasheet with complete property values for TAROMID B 280 Z3 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Polyamide 6 elastomer modified, very high impact resistance also at low temperature, high viscosity, very good chemical resistance to oils, solvents and other chemical substances.

Available: all colors, lubricated (W), and UV-stabilized (L).
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Lubricant
  • UV Stabilizer
  
Features 
  • Good Chemical Resistance
  • Good UV Resistance
  • High Viscosity
  • Low Temperature Impact Resistance
  • Lubricated
  • Oil Resistant
  • Solvent Resistant
  • Ultra High Impact Resistance
Appearance 
  • Colors Available
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption
      
73°F, 24 hr
%
 ASTM D570, ISO 62
Saturation
%
 ASTM D570
Saturation, 73°F
%
 ISO 62
Granule Humidity
%
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638, ISO 527-2
Tensile Strength
     ASTM D638, ISO 527-2
Yield
psi
  
Break
psi
  
Tensile Elongation (Break)
%
 ASTM D638, ISO 527-2
Flexural Modulus
psi
 ASTM D790, ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength 2
     ASTM D256, ISO 179
-4°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength 2
     ASTM D256, ISO 179
-4°F
 
  
73°F
 
  
Notched Izod Impact
     ISO 180, ASTM D256
-4°F, 0.126 in
ft·lb/in
  
73°F, 0.126 in
ft·lb/in
  
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648, ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B50, ASTM D1525 3
Ball Pressure Test (257°F)
 
 VDE 0470
Melting Temperature
°F
 ASTM D211, ISO 121
CLTE - Flow (-22 to 86°F)
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Comparative Tracking Index (Solution A)
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
     UL 94
0.0382 in
 
  
0.0630 in
 
  
0.126 in
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: TAROMID B 280 Z3, TAROMID B , TAROMIDB280Z3, TAROMIDB, B 280 Z 3, B280 Z3, B280, 280 Z 3, B280Z3, 280 Z3, 280Z, Z3, 280Z3, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, Taro Plast, Polyamide6, Nylon6, Z280, 280B
Generic Name
Generic Name may also be described by the following terms: PA6.
Features
Features may also be described by the following terms: Ultra High Impact Resistance, Low Temperatuer Impact Resistance, Low Temp Impact Resistance, Good Chemical Resistance, Chemical Resistant, High Viscosity, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
      
--
°F
  
Pre-heater
°F
  
Drying Time
      
--
hr
  
Pre-heater
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
26x4x50 mm
3Rate A (50°C/h), Loading 2 (50 N)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.