IDES Prospector Already have an account? Login Here

IDES

TARODUR 150

Acrylonitrile Butadiene Styrene

Supplied by Taro Plast S.p.A.

The technical datasheet with complete property values for TARODUR 150 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
ABS high impact strength, and good heat resistance.

Approved FIAT SA 90.150 BL and ABS 95.150

Available: all colors, UV stabilized (L), heat stabilized (H) and antistatic (AS).
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Antistatic
  • Heat Stabilizer
  • UV Stabilizer
Features 
  • Antistatic
  • Good UV Resistance
  • Heat Stabilized
  • High Impact Resistance
  • Medium Heat Resistance
Appearance 
  • Colors Available
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (220°C/10.0 kg)
g/10 min
 ASTM D1238, ISO 1133
Molding Shrinkage
     ASTM D955
Flow
in/in
  
Across Flow
in/in
  
Water Absorption (73°F, 24 hr)
%
 ASTM D570, ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638, ISO 527-2
Tensile Strength (Yield)
psi
 ASTM D638, ISO 527-2
Tensile Elongation (Break)
%
 ASTM D638, ISO 527-2
Flexural Modulus
psi
 ASTM D790, ISO 178
Flexural Strength
      
-- 2
psi
 ISO 178
Yield
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength 3 (73°F)
ft·lb/in²
 ASTM D256, ISO 179
Notched Izod Impact (73°F, 0.126 in)
ft·lb/in
 ISO 180, ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648, ISO 75-2/A
Vicat Softening Temperature
      
--
°F
 ASTM D1525 4, ISO 306/A50 4
--
°F
 ASTM D1525 5, ISO 306/B50 5
Ball Pressure Test (167°F)
 
 VDE 0470
CLTE - Flow (-22 to 86°F)
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Flammability
Nominal Value
Unit
Test Method
Glow Wire Ignition Temperature (0.0787 in)
°F
 IEC 60695-2-13
Oxygen Index
%
 ASTM D2863
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: TARODUR 150, TARODUR , TARODUR150, 150, Acrylonitrile Butadiene Styrene, ABS, Taro Plast, AcrylonitrileButadieneStyrene
Features
Features may also be described by the following terms: High Impact Resistance, Medium Heat Resistance, Heat Stabilized, Heat-ageing Stabilized, Heat Ageing Stabilized, Heat-aging Stabilized, Heat Aging Stabilized, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
      
--
°F
  
Pre-heater
°F
  
Drying Time
      
--
hr
  
Pre-heater
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Notes
1Typical properties: these are not to be construed as specifications.
2Yield
36x4x50 mm
4Rate A (50°C/h), Loading 1 (10 N)
5Rate A (50°C/h), Loading 2 (50 N)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.