IDES Prospector Already have an account? Login Here

IDES

TAROBLEND 45

Acrylonitrile Butadiene Styrene + PC

Supplied by Taro Plast S.p.A.

The technical datasheet with complete property values for TAROBLEND 45 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
PC/ABS alloy medium thermal resistance, good flow and mechanical properties.

FORD TL 522 31 (Type A)

Available: all colors, UV-stablized (L), antistatic (AS).
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Antistatic
  • UV Stabilizer
  
Features 
  • Antistatic
  • Good Flow
  • Good UV Resistance
  • High Heat Resistance
  
Appearance 
  • Colors Available
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (260°C/5.0 kg)
g/10 min
 ASTM D1238, ISO 1133
Molding Shrinkage
     ASTM D955
Flow
in/in
  
Across Flow
in/in
  
Water Absorption
      
73°F, 24 hr
%
 ASTM D570, ISO 62
Saturation
%
 ASTM D570
Saturation, 73°F
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638, ISO 527-2
Tensile Strength (Yield)
psi
 ASTM D638, ISO 527-2
Tensile Elongation (Break)
%
 ASTM D638, ISO 527-2
Flexural Modulus
psi
 ASTM D790, ISO 178
Flexural Strength
      
-- 2
psi
 ISO 178
Break
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength 3 (73°F)
ft·lb/in²
 ASTM D256, ISO 179
Charpy Unnotched Impact Strength 3 (73°F)
 
 ISO 179, ASTM D256
Notched Izod Impact (73°F, 0.126 in)
ft·lb/in
 ISO 180, ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648, ISO 75-2/A
Max. Continuous Use Temperature 4
°F
 IEC 60216
Vicat Softening Temperature
      
--
°F
 ASTM D1525 5, ISO 306/A50 5
--
°F
 ASTM D1525 6, ISO 306/B50 6
Ball Pressure Test (257°F)
 
 VDE 0470
CLTE - Flow (-22 to 86°F)
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength (0.0787 in)
V/mil
 ASTM D149
Comparative Tracking Index (Solution A)
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0630 in)
 
 UL 94
Glow Wire Ignition Temperature (0.0787 in)
°F
 IEC 60695-2-13
Oxygen Index
%
 ASTM D2863
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: TAROBLEND 45, TAROBLEND , TAROBLEND45, 45, Acrylonitrile Butadiene Styrene + PC, Acrylonitrile Butadiene Styrene PC, Acrylonitrile Butadiene Styrene : PC, Acrylonitrile Butadiene Styrene / PC, Acrylonitrile Butadiene Styrene - PC, Acrylonitrile Butadiene Styrene _ PC, Acrylonitrile Butadiene Styrene PC, ABS+PC, ABSPC, ABS:PC, ABS/PC, ABS-PC, ABS_PC, ABS PC, Acrylonitrile Butadiene Styrene, ABS, Taro Plast, AcrylonitrileButadieneStyrenePC, AcrylonitrileButadieneStyrene, AcrylonitrileButadieneStyrene_PC
Features
Features may also be described by the following terms: Good Flow, High Heat Resistance, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
      
--
°F
  
Pre-heater
°F
  
Drying Time
      
--
hr
  
Pre-heater
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Notes
1Typical properties: these are not to be construed as specifications.
2Break
36x4x50 mm
420000 hrs
5Rate A (50°C/h), Loading 1 (10 N)
6Rate A (50°C/h), Loading 2 (50 N)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.