IDES Prospector Already have an account? Login Here

IDES

TAROLOY 50

Polycarbonate + PBT

Supplied by Taro Plast S.p.A.

The technical datasheet with complete property values for TAROLOY 50 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Good Chemical Resistance
  • Good Dimensional Stability
  • Good Impact Resistance
  • Good Strength
  • Low Temperature Impact Resistance
Appearance 
  • Colors Available
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (260°C/5.0 kg)
g/10 min
 ISO 1133
Molding Shrinkage
     Internal Method
Across Flow
%
  
Flow
%
  
Water Absorption
     ISO 62
73°F, 24 hr
%
  
Saturation, 73°F
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1
Tensile Stress
     ISO 527-2/50
Yield
psi
  
Break
psi
  
Tensile Strain (Break)
%
 ISO 527-2/50
Flexural Modulus 2
psi
 ISO 178
Flexural Strength 2
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eA
Notched Izod Impact (73°F)
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
 ISO 75-2/A
Max. Continuous Use Temperature 3
°F
 IEC 60216
Vicat Softening Temperature
°F
 ISO 306/A50
Ball Pressure Test (275°F)
 
 IEC 60695-10-2
CLTE - Flow (-22 to 86°F)
in/in/°F
 ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 IEC 60093
Comparative Tracking Index (Solution A)
V
 IEC 60112
Electric Strength (0.118 in)
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0630 in)
 
 UL 94
Glow Wire Flammability Index (0.0787 in)
°F
 IEC 60695-2-12
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: TAROLOY 50, TAROLOY , TAROLOY50, 50, Polycarbonate + PBT, Polycarbonate PBT, Polycarbonate : PBT, Polycarbonate / PBT, Polycarbonate - PBT, Polycarbonate _ PBT, Polycarbonate PBT, PC+PBT, PCPBT, PC:PBT, PC/PBT, PC-PBT, PC_PBT, PC PBT, Polycarbonate, PC, Taro Plast, PolycarbonatePBT, Polycarbonate_PBT
Features
Features may also be described by the following terms: Good Impact Resistance, Good Strength, Low Temperatuer Impact Resistance, Low Temp Impact Resistance, Good Dimensional Stability, Dimensionally Stable, Good Chemical Resistance, Chemical Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
      
--
°F
  
Pre-heater
°F
  
Drying Time
      
--
hr
  
Pre-heater
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Notes
1Typical properties: these are not to be construed as specifications.
20.039 in/min
320000 hrs
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.