IDES Prospector Already have an account? Login Here

IDES

Edgetek™ PC-20GF/000

Polycarbonate

Glass Fiber Reinforcement

Supplied by PolyOne Corporation

The technical datasheet with complete property values for Edgetek™ PC-20GF/000 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  • South America
Filler / Reinforcement 
  • Glass Fiber Reinforcement
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2
psi
 ASTM D638
Tensile Strength 2 (Break)
psi
 ASTM D638
Tensile Elongation 2 (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Compressive Strength
psi
 ASTM D695
Shear Strength
psi
 ASTM D732
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F, 0.250 in, Injection Molded)
ft·lb/in
 ASTM D256A
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (M-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Annealed, 0.125 in
°F
  
264 psi, Annealed, 0.125 in
°F
  
CLTE - Flow
in/in/°F
 ASTM D696
Thermal Conductivity
Btu·in/hr/ft²/°F
 ASTM C177
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Edgetek™ PC-20GF/000, Edgetek PC20GF000, Edgetek™ , Edgetek, EdgetekPC20GF000, PC, PC 20 GF 000, PC-20GF/000, PC20GF000, PC-20GF:000, PC-20GF+000, PC-20GF-000, PC-20GF_000, PC-20GF 000, PC:20GF/000, PC/20GF/000, PC+20GF/000, PC_20GF/000, PC 20GF/000, PC20, 20GF, GF000, PC20GF_000, PC20GF 000, PC_20GF000, PC 20GF000, Polycarbonate, PolyOne, 20PC
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Type I, 0.20 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.