IDES Prospector Already have an account? Login Here

IDES

YUCLAIR® FT210

High Density Polyethylene

Supplied by SK Corporation

The technical datasheet with complete property values for YUCLAIR® FT210 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
YUCLAIR FT210 is homopolymer designed for use in casting film application.
YUCLAIR FT210 provides stronger film than ones made from competitive HDPE film grades. Therefore YUCLAIR FT210 shows superior stiffness, tensile strength, gel-free, and processibility.
YUCLAIR FT210 can be processed readily into casting film using standard extrusion techniques.
YUCLAIR FT210 complies with FDA regulations in 21 CFR177.1520 for all food contact.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • North America
Features 
  • Food Contact Acceptable
  • Good Processability
  • High Stiffness
  • High Tensile Strength
  • Homopolymer
Uses 
  • Cast Film
  • Film
  
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Cast Film
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ASTM D1238
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Optical
Nominal Value
Unit
Test Method
Haze
%
 ASTM D1003
Additional Information
Tensile Strength at Yield, ASTM D638, MD/TD: 270/270 kg/cm²
Tensile Strength at Break, ASTM D638, MD/TD: 370/330 kg/cm²
Elongation at Break, ASTM D638, MD/TD: 940%/970%
Elmendorf Tear Strength, ASTM D1922, MD: 1 kg/cm
Elmendorf Tear Strength, ASTM D1922, TD: 2 kg/cm
Spencer Impact Strength, ASTM D3420: 5 kg-cm
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: YUCLAIR® FT210, YUCLAIR FT210, YUCLAIR® , YUCLAIR, YUCLAIRFT210, FT 210, FT210, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, SK Corporation, PolyethyleneHighDensity, 210FT
Features
Features may also be described by the following terms: High Tensile Strength, High Stiffness, Good Processability, Easy Processing.
Uses
Uses may also be described by the following terms: Cast Film.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Die Temperature
°F
  
Extrusion Notes
Screw dia 50, Die width 450
Die gap 0.8, Screw RPM 31, L/S 7
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.