IDES Prospector Already have an account? Login Here

IDES

Vi-Chem PVC NFC87-80E

Rigid Polyvinyl Chloride

Supplied by Vi-Chem Corporation

The technical datasheet with complete property values for Vi-Chem PVC NFC87-80E is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Medium Rigidity
Automotive Specifications 
Forms 
  • Pellets
Processing Method 
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2, 3 (Yield)
psi
 ASTM D638
Tensile Elongation 2, 3 (Break)
%
 ASTM D638
Elastomers
Nominal Value
Unit
Test Method
Tear Strength 4
lbf/in
 ASTM D1004
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A, 15 sec)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Cold Flexibility 5 (-22°F, 0.98 in)
 
  
Aging
Nominal Value
Unit
Test Method
Change in Tensile Strength in Air (176°F, 1000 hr)
%
 ASTM D412
Change in Ultimate Elongation in Air (176°F, 1000 hr)
%
 ASTM D412
Change in Mass in Air (176°F, 1000 hr)
%
 ASTM D412
Additional Information
Nominal Value
Unit
Test Method
Stain Resistance
      
-- 6
 
  
-- 7
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Vi-Chem PVC NFC87-80E, ViChem PVC NFC8780E, Vi-Chem PVC , ViChem PVC, Vi:Chem PVC, Vi/Chem PVC, Vi+Chem PVC, Vi_Chem PVC, Vi Chem PVC, ViChemPVCNFC8780E, ViChemPVC, NFC 87, PVCNFC 87 80 E, PVCNFC 87, Vi_ChemPVC, PVCNFC87-80E, PVCNFC8780E, PVCNFC87:80E, PVCNFC87/80E, PVCNFC87+80E, PVCNFC87_80E, PVCNFC87 80E, PVCNFC87, NFC 87 80 E, NFC87-80E, NFC8780E, NFC87:80E, NFC87/80E, NFC87+80E, NFC87_80E, NFC87 80E, NFC87, 8780, 80E, Polyvinyl Chloride, Rigid, Polyvinyl Chloride Rigid, PVC, Rigid, PVC Rigid, Polyvinyl Chloride, PVC, Vi-Chem, PolyvinylChlorideRigid, PVCRigid, PolyvinylChloride, 87NFC, 87PVCNFC
Features
Features may also be described by the following terms: Medium Rigidity, Good Rigidity.
Automotive Specifications
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): GM (1).
Notes
1Typical properties: these are not to be construed as specifications.
2Type IV, 20 in/min
3Die C
42.0 in/min
5GM9503
6Asphalt, Delta E
7Hydrogen Sulfide, FLTM 102-01, AATCC5
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.