IDES Prospector Already have an account? Login Here

IDES

Marlex® PP AGN-380

Polypropylene Impact Copolymer

Supplied by Phillips Sumika Polypropylene Company

The technical datasheet with complete property values for Marlex® PP AGN-380 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Durable
  • Food Contact Acceptable
  • Impact Copolymer
Uses 
  • Automotive Interior Trim
  • Household Goods
  
Agency Ratings 
  •  1
Automotive Specifications 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183, ASTM D1505
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ASTM D1238, ISO 1133
Molding Shrinkage (73°F, 48 hr)
%
 ISO 294-4
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
      
Yield, Injection Molded 3
psi
 ASTM D638
Yield, Injection Molded
psi
 ISO 527-2/50
Flexural Modulus
      
Secant: Injection Molded 4
psi
 ASTM D790
Tangent: Injection Molded 5
psi
 ASTM D790
Injection Molded 6
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
      
-22°F, Injection Molded
ft·lb/in
 ASTM D256
73°F, Injection Molded
ft·lb/in
 ASTM D256
-40°F
ft·lb/in²
 ISO 180
73°F
ft·lb/in²
 ISO 180
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785, ISO 2039-2
Durometer Hardness (Shore D, Injection Molded)
 
 ASTM D2240, ISO 868
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
      
66 psi, Unannealed, Injection Molded
°F
 ASTM D648
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed, Injection Molded
°F
 ASTM D648
264 psi, Unannealed
°F
 ISO 75-2/A
Additional Information
The value listed as Molding Shrinkage, ISO 294-4, 48 hr, 23°C may not have been tested according to the ISO 294-4 standard.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Marlex® PP AGN-380, Marlex PP AGN380, Marlex® PP , Marlex PP, MarlexPPAGN380, MarlexPP, AGN, PPAGN-380, PPAGN380, PPAGN:380, PPAGN/380, PPAGN+380, PPAGN_380, PPAGN 380, PPAGN, AGN-380, AGN380, AGN:380, AGN/380, AGN+380, AGN_380, AGN 380, Polypropylene Impact Copolymer, PP Impact Copolymer, Polypropylene, PP, Phillips Sumika, PolypropyleneImpactCopolymer, PPImpactCopolymer, 380AGN, 380PPAGN
Features
Features may also be described by the following terms: Impact Copolymer.
Uses
Uses may also be described by the following terms: Household Goods, Housewares.
Automotive Specifications
This plastic material has approval for 6 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): GM (2), TOYOTA (4).
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Injection
Nominal Value
Unit
 
Suggested Shot Size
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Injection Notes
Melt temperature above 500°F (260°C) may cause degredation and changes to resin properties.
First stage injection pressure: Maximize
Screw speed: 30 to 60%
Packaging pressure: Minimize
Notes
1except for articles used for packing or holding food during cooking
2Typical properties: these are not to be construed as specifications.
32.0 in/min
40.051 in/min
50.51 in/min
60.079 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.