IDES Prospector Already have an account? Login Here

IDES

Glasrod HIR

Thermoset Polyester

Supplied by Glastic Corporation

The technical datasheet with complete property values for Glasrod HIR is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Glasrod HIR is a solid rod and bar fiberglass-reinforced thermoset polyester shape that exhibits properties desirable for a wide range of structural and electrical applications. Highest physical properties. Electrical properties and high temperature capabilities Class H (200°C). Dimensional stability and 100,000 psi flexural strength. Resistant to fluids commonly used around electrical equipment. Greater cost efficiency than epoxy, phenolic, nylon or brass rod. Available in Round Rod.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Good Dimensional Stability
  • High Heat Resistance
  • High Strength
  • Low to No Water Absorption
  • Solvent Resistant
Uses 
  • Electrical/Electronic Applications
  • Insulation
  • Rods
  • Structural Parts
  
Appearance 
  • Light Green
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength (Yield)
psi
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength (Yield)
psi
 ASTM D790
Shear Strength
psi
 ASTM D732
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
CLTE - Flow
in/in/°F
 ASTM D696
Thermal Conductivity
Btu·in/hr/ft²/°F
 ASTM C177
Electrical
Nominal Value
Unit
Test Method
Dielectric Strength (1.00 in, in Oil)
V/mil
 ASTM D149
Dielectric Constant (60 Hz)
 
 ASTM D150
Arc Resistance
sec
 ASTM D495
Additional Information
The value listed as Shear Strength ASTM D732 was tested in acordance with ASTM D3914.
Insulation Resistance, ASTM D257: 1e10 ohms
Compressive Strength, ASTM D695, Axial: 60000 psi
Compressive Strength, ASTM D695, Transverse: 16000 psi
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Glasrod HIR, Glasrod , GlasrodHIR, HIR, Polyester, Thermoset, Polyester Thermoset, Polyester, TS, Polyester TS, Thermoset, TS, Glastic, PolyesterThermoset, PolyesterTS
Features
Features may also be described by the following terms: Low Water Absorption, Low Moisture Absorption, Water Resistant, Moisure Resistant, High Strength, High Heat Resistance, Good Dimensional Stability, Dimensionally Stable.
Uses
Uses may also be described by the following terms: Rods, Rod, Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.