|
Specific Gravity
|
|
|
|
|
--
|
|
|
ASTM D792 |
|
--
|
|
g/cm³
|
ISO 1183 |
|
Tensile Modulus (0.0750 in, Compression Molded)
|
|
psi
|
ASTM D638, ISO 527-2 |
|
Tensile Strength (Yield, 0.0750 in, Compression Molded)
|
|
psi
|
ASTM D638, ISO 527-2 |
|
Tensile Elongation (Break, 0.0750 in, Compression Molded)
|
|
%
|
ASTM D638, ISO 527-2 |
|
Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel)
|
|
mg
|
ASTM D1044 |
|
Tensile Set
|
|
%
|
ASTM D412 |
|
Tear Strength 2 (75°F)
|
|
lbf/in
|
ASTM D624 |
|
Compression Set
|
|
|
ASTM D395B, ISO 815 |
|
75°F, 22.0 hr
|
|
%
|
|
|
212°F, 22.0 hr
|
|
%
|
|
|
Clash-Berg Modulus (-5°F)
|
|
psi
|
ASTM D1043 |
|
Durometer Hardness (Shore A, 0.0750 in, Compression Molded)
|
|
|
ASTM D2240 |
|
IRHD Hardness
|
|
|
ISO 48 |
|
Change in Volume
|
|
|
ASTM D471 |
|
75°F, 168 hr, in Reference Fuel B
|
|
%
|
|
|
212°F, 168 hr, in ASTM Oil #1
|
|
%
|
|
|
212°F, 168 hr, in ASTM Oil #3
|
|
%
|
|
|
The value listed as Density-Specific Gravity, ASTM D792, was tested in accordance with ASTM D471.
Aging Tensile Strength, ASTM D573, 7 days, 257°F: 37psi
Aging Elongation At Break, ASTM D573 and ISO 188: 71%
Fluid Resistance 7 Days in ASTM Oil no. 1, ISO 1817, at 212 °F: -10%
Fluid Resistance 7 Days in IRM 903 Oil no. 3, ISO 1817, at 212 °F: -23%
Fluid Resistance 7 Days in ASTM Ref. Fuel no. B, ISO 1817, at 75 °F: 36%
Rheological Viscosity, ASTM D3835, 1/300s at 374°F: 550Pa-s
|
|
This supplier and product may also be known by these terms: APA, Advanced Polymer Alloys is a division of Ferro
Product names can be difficult to match. You may have searched any one of these terms to find this product: Alcryn® 2090 BK, Alcryn 2090 BK, Alcryn® , Alcryn, Alcryn2090BK, 2090 BK, 2090BK, Melt Processable Rubber, MPR, Thermoplastic Elastomer, TPE, APA, MeltProcessableRubber, ThermoplasticElastomer, BK2090
|
|
Features may also be described by the following terms: Good Weather Resistance, Weather Resistant, High Heat Resistance, High Flow, High Melt, High MFI, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
|
|
Uses may also be described by the following terms: Gaskets, Gasketing, Engineering Parts, Tubing, Tube.
|
|
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1).
|