IDES Prospector Already have an account? Login Here

IDES

Versaflex™ OM 9-801N

Thermoplastic Elastomer

Supplied by GLS Thermoplastic Elastomers

The technical datasheet with complete property values for Versaflex™ OM 9-801N is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Versaflex™ OM 9-801N is designed for overmolding onto a wide variety of substrates including PC, ABS, PC/ABS, HIPS, PPO, HDPE, acetal, acrylic and copolyester.
  • Bonds to a Variety Of Substrates
  • Rubbery Feel
  • Soft Touch
  • Very Good Surface Aesthetics
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  • South America
Features 
  • Good Surface Finish
Uses 
  • Flexible Grips
  • General Purpose
  • Overmolding
  • Soft Touch Applications
  • Sporting Goods
Agency Ratings 
 
RoHS Compliance 
Automotive Specifications 
Appearance 
  • Natural Color
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR)
     ASTM D1238
190°C/2.16 kg
g/10 min
  
200°C/5.0 kg
g/10 min
  
Molding Shrinkage - Flow
in/in
 ASTM D955
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress 2, 3
     ASTM D412
100% Strain, 73°F
psi
  
300% Strain, 73°F
psi
  
Tensile Strength 2, 3 (Break, 73°F)
psi
 ASTM D412
Tensile Elongation 2, 3 (Break, 73°F)
%
 ASTM D412
Tear Strength
lbf/in
 ASTM D624
Compression Set (73°F, 22.0 hr)
%
 ASTM D395B
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A, 10 sec)
 
 ASTM D2240
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0591 in)
 
 UL 94
Fill Analysis
Nominal Value
Unit
Test Method
Apparent Viscosity (392°F, 11200 sec^-1)
Pa·s
 ASTM D3835
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Versaflex™ OM 9-801N, Versaflex OM 9801N, Versaflex™ , Versaflex, VersaflexOM9801N, OM 9, OM 9 801 N, OM 9-801N, OM 9801N, OM 9:801N, OM 9/801N, OM 9+801N, OM 9_801N, OM 9 801N, OM9, 9801, 801N, OM9801N, OM9_801N, Thermoplastic Elastomer, TPE, GLS, ThermoplasticElastomer, 9OM
Features
Features may also be described by the following terms: Good Surface Finish.
Uses
Uses may also be described by the following terms: Flexible Grips.
Automotive Specifications
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FMVSS (1).
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1), UL (1).
Injection
Nominal Value
Unit
 
Suggested Max Regrind
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Injection Notes
Color concentrates with polyethylene (PE) or EVA carriers are most suitable for coloring Versaflex™ OM 9-801N. Typical letdown ratios are 50:1 to 25:1 - loading levels should be as low as possible to minimize the effect on adhesion. A high color match consistency can be obtained by the use of precolored compounds available from GLS. Concentrates based on PVC should not be used. The final determination of color concentrate suitability should be determined by customer trials. trials.

Purge thoroughly before and after use of this product with a low flow (0.5 - 2.5 MFR) polystyrene (PS) or polypropylene (PP).

Regrind levels up to 20% can be used with Versaflex™ OM 9-801N with minimal property loss, provided that the regrind is free of contamination. To minimize losses during molding, the melt temperature should remain as low as possible. The final determination of regrind effectiveness should be determined by the customer.

Versaflex™ OM 9-801N has good melt stability. Maximum residence times may vary, depending on the size of the barrel. Generally, the barrel should be emptied if it is idle for periods of 5 - 8 minutes or longer.

Drying is not Required

Injection Speed: 0.5 to 3 in/sec
1st Stage - Boost Pressure: 500 to 900 psi
2nd Stage - Hold Pressure: 70% of Boost
Hold Time (Thick Part): 4 to 10 sec
Hold Time (Thin Part): 1 to 3 sec
Notes
1Typical properties: these are not to be construed as specifications.
2Die C
32 hr
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.