IDES Prospector Already have an account? Login Here

IDES

Arnite® A06 101

Polyethylene Terephthalate

Supplied by DSM Engineering Plastics

The technical datasheet with complete property values for Arnite® A06 101 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Very high Viscosity
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Profile Extrusion
  • Sheet Extrusion
Physical
Nominal Value
Unit
Test Method
Density
      
--
g/cm³
 ISO 1183
--
lb/in³
 ISO 1183 2
Melt Volume-Flow Rate (MVR) (270°C/2.16 kg)
in³/10min
 ISO 1133
Water Absorption
      
Equilibrium, 73°F, 50% RH
%
 ISO 62
Equilibrium
%
 ISO 62 2
Mechanical
Nominal Value
Unit
Test Method
Tensile modulus
psi
 ISO 527-2 2
Tensile Stress (Yield)
psi
 ISO 527-2 2
Tensile Strain (Yield)
%
 ISO 527-2 2
Nominal strain at break
%
 ISO 527-2 2
Impact
Nominal Value
Unit
Test Method
Charpy impact strength (73°F)
ft·lb/in²
 ISO 179/1eU 2
Thermal
Nominal Value
Unit
Test Method
Melting Temperature
      
-- 3
°F
 ISO 11357-3
-- 4
°F
 ISO 11357-3 2
Electrical
Nominal Value
Unit
Test Method
Surface resistivity
ohms
 IEC 60093 2
Volume resistivity
ohm·in
 IEC 60093 2
Flammability
Nominal Value
Unit
Test Method
Burning Behav. at 1.6mm nom. thickn. (0.04 in, UL)
 
 ISO 1210 2
Oxygen index
%
 ISO 4589-2 2
Additional Information
Nominal Value
Unit
Test Method
RSV 5
 
 Internal Method
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Arnite® A06 101, Arnite A06 101, Arnite® , Arnite, ArniteA06101, A 06 101, A06 101, A06, 06101, A06101, Polyethylene Terephthalate, PET, Polyester, DSM EP, PolyethyleneTerephthalate, 06A
Features
Features may also be described by the following terms: Very High Viscosity.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted.
310°C/min
418 °F/min
5m-cresol, 1g/100ml
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.