IDES Prospector Already have an account? Login Here

IDES

Xantar® SF 2220

Polycarbonate

Glass Fiber Reinforcement, 20%

Supplied by Mitsubishi Engineering-Plastics Corp

The technical datasheet with complete property values for Xantar® SF 2220 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 20% Filler by Weight
Additive 
  • Flame Retardant
Features 
  • Flame Retardant
  • Foamable
  
Uses 
  • Structural Foam
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
     ISO 1183
-- 2
g/cm³
  
--
g/cm³
  
Melt Volume-Flow Rate (MVR) (300°C/1.2 kg)
in³/10min
 ISO 1133
Water Absorption (Saturation, 73°F)
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress (Break)
psi
 ISO 527-2
Tensile Strain (Break)
%
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Flexural Strength
psi
 ISO 178
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
 ISO 75-2/A
Ball Pressure Test (257°F)
 
 IEC 60695-10-2
CLTE - Flow
in/in/°F
 ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Relative Permittivity
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Dissipation Factor
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Flammability
Nominal Value
Unit
Test Method
Burning Behav. at 1.6mm nom. thickn. (0.19 in, UL)
 
 ISO 1210 3
Burning Behav. 5V at thickness h (0.189 in, UL)
 
 ISO 10351 3
Flammability Classification (0.189 in)
 
 IEC 60695-11-10, -20
Oxygen Index
%
 ISO 4589-2
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Xantar® SF 2220, Xantar SF 2220, Xantar® , Xantar, XantarSF2220, SF 2220, SF2220, Polycarbonate, PC, Mitsubishi EP, 2220SF
Uses
Uses may also be described by the following terms: Structural Foam.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Suggested Shot Size
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Back Pressure
psi
  
Screw L/D Ratio
 
  
Screw Compression Ratio
 
  
Notes
1Typical properties: these are not to be construed as specifications.
2Foamed
3Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.