IDES Prospector Already have an account? Login Here

IDES

TOYOBO PPS TS401 HS

Polyphenylene Sulfide

Glass Fiber Reinforcement, 40%

Supplied by TOYOBO America, Inc.

The technical datasheet with complete property values for TOYOBO PPS TS401 HS is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 40% Filler by Weight
Features 
  • High Flow
  • High Strength
  • Low Viscosity
  • Ultra High Toughness
  
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage
     ASTM D955
Flow
in/in
  
Across Flow
in/in
  
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength (Yield)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength (Yield)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
CLTE
     ASTM D696
Flow
in/in/°F
  
Transverse
in/in/°F
  
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Dielectric Constant
     ASTM D150
1 kHz
 
  
1 MHz
 
  
Dissipation Factor
     ASTM D150
1 kHz
 
  
1 MHz
 
  
Arc Resistance
sec
 ASTM D495
Comparative Tracking Index
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
 
 UL 94
Additional Information
Flexural Elongation, ASTM D790: 2.3 %
HDT 264 psi, ASTM D648: >260 °C
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: TOYOBO PPS TS401 HS, TOYOBO PPS , TOYOBOPPSTS401HS, TOYOBOPPS, PPSTS 401 HS, PPSTS401 HS, PPSTS401, PPS, TS 401 HS, PPSTS401HS, TS401 HS, TS401, 401HS, TS401HS, Polyphenylene Sulfide, Toyobo, PolyphenyleneSulfide, 401TS, 401PPSTS
Features
Features may also be described by the following terms: Ultra High Toughness, Low Viscosity, High Strength, High Flow, High Melt, High MFI.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.