IDES Prospector Already have an account? Login Here

IDES

RTP Compounds 907

Polysulfone

Glass Fiber Reinforcement, 40%

Supplied by RTP Company

The technical datasheet with complete property values for RTP Compounds 907 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 40% Filler by Weight
RoHS Compliance 
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow (0.125 in)
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Yield)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.125 in)
ft·lb/in
 ASTM D256
Unnotched Izod Impact (0.125 in)
ft·lb/in
 ASTM D4812
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
CLTE - Flow
in/in/°F
 ASTM E831
Thermal Conductivity 2
Btu·in/hr/ft²/°F
 ASTM E1461
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength 3 (in Oil)
V/mil
 ASTM D149
Dielectric Constant (1 MHz)
 
 ASTM D150
Dissipation Factor (1 MHz)
 
 ASTM D150
Arc Resistance
sec
 ASTM D495
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0591 in, Values per RTP Company testing.)
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: RTP Compounds 907, RTP Compounds , RTPCompounds907, RTPCompounds, Compounds 907, Compounds907, Compounds, 907, Polysulfone, PSU, RTP, 907Compounds
Injection
Nominal Value
Unit
 
Drying Temperature - Desiccant Dryer
°F
  
Drying Time - Desiccant Dryer
hr
  
Dew Point - Desiccant Dryer
°F
  
Suggested Max Moisture
%
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Notes
1Typical properties: these are not to be construed as specifications.
2Through-plane
3Method A (Short-Time)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.