IDES Prospector Already have an account? Login Here

IDES

DENITER 0037 ST

Polybutylene Terephthalate

Supplied by Vamp Tech

The technical datasheet with complete property values for DENITER 0037 ST is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Super tough PBT, very good elongation and flexibility
General  
Material Status 
  • Commercial: Discontinued
Availability 
  • Europe
Features 
  • Good Flexibility
  • High Elongation
  • Ultra High Toughness
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield)
psi
 ASTM D638, ISO 527-2
Tensile Elongation (Yield)
%
 ASTM D638, ISO 527-2
Flexural Modulus
psi
 ASTM D790, ISO 178
Flexural Strength
      
--
psi
 ISO 178
Yield
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Charpy Unnotched Impact Strength
ft·lb/in²
 ISO 179
Notched Izod Impact Strength
ft·lb/in²
 ISO 180
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
      
66 psi, Unannealed
°F
 ASTM D648, ISO 75-2/B
264 psi, Unannealed
°F
 ASTM D648, ISO 75-2/A
Vicat Softening Temperature
      
--
°F
 ASTM D1525 2, ISO 306/A50 2
--
°F
 ASTM D1525 3, ISO 306/B50 3
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Comparative Tracking Index
     IEC 60112
Solution A
V
  
Solution B
V
  
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
     UL 94
0.0315 in
 
  
0.0630 in
 
  
0.126 in
 
  
Glow Wire Ignition Temperature
°F
 IEC 60695-2-13
Oxygen Index
%
 ASTM D2863
Additional Information
Ball Penetration Test, IEC 335, 125 °C: Yes
Ball Penetration Test, IEC 335, 165 °C: No
Elongation at Yield, ASTM D638: >100%
Flame Resistance. CSA C22-2: No
Operating Temperature Limit: 120°C
Operating Temperature, IEC 216: 100°C
Strain at Yield, ISO 527:>100%
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: DENITER 0037 ST, DENITER , DENITER0037ST, 0037 ST, 0037ST, Polybutylene Terephthalate, PBT, Polyester, Vamp Tech, PolybutyleneTerephthalate, ST0037
Features
Features may also be described by the following terms: Ultra High Toughness, Good Flexibility, Flexible, High Elongation.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Rate A (50°C/h)
3Rate B (120°C/h)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.