VAMPAMID 6 3025 V0 Vamp Tech Polyamide 6 (Mineral Filler)

Product Description

UL 94 V0, 30% mineral filled, good electrical properties, excellent dimensional stability

General

Material Status

Commercial: Discontinued

Availability

Europe

Filler / Reinforcement

Mineral Filler

Features

Good Dimensional Stability

Good Electrical Properties

Forms

Pellets

Physical	Nominal Value	Unit	Test Method
Specific Gravity
--			ASTM D792
--		g/cm³	ISO 1183
Molding Shrinkage - Flow		in/in	ASTM D955
Water Absorption (24 hr)		%	ASTM D570
Mechanical	Nominal Value	Unit	Test Method
Tensile Strength (Yield)		psi	ASTM D638, ISO 527-2
Tensile Elongation (Yield)		%	ASTM D638, ISO 527-2
Flexural Modulus		psi	ASTM D790, ISO 178
Flexural Strength
--		psi	ISO 178
Yield		psi	ASTM D790
Impact	Nominal Value	Unit	Test Method
Charpy Unnotched Impact Strength		ft·lb/in²	ISO 179
Notched Izod Impact Strength		ft·lb/in²	ISO 180
Thermal	Nominal Value	Unit	Test Method
Deflection Temperature Under Load
66 psi, Unannealed		°F	ASTM D648, ISO 75-2/B
264 psi, Unannealed		°F	ASTM D648, ISO 75-2/A
Vicat Softening Temperature
--		°F	ASTM D1525², ISO 306/A50²
--		°F	ASTM D1525³, ISO 306/B50³
CLTE - Flow		in/in/°F	ASTM D696
Electrical	Nominal Value	Unit	Test Method
Dielectric Strength		V/mil	ASTM D149
Comparative Tracking Index			IEC 60112
Solution A		V
Solution B		V
Needle Flame Test			IEC 60695-11-5
Flammability	Nominal Value	Unit	Test Method
Flame Rating - UL			UL 94
0.0315 in
0.0630 in
0.126 in
Glow Wire Ignition Temperature		°F	IEC 60695-2-13
Oxygen Index		%	ASTM D2863
Additional Information
Ball Penetration Test, IEC 335, 125 °C: Yes Ball Penetration Test, IEC 335, 165 °C: Yes Density, ASTM D1238: 1.58 to 1.59g/cm³ Density, ISO 1183: 1.58 to 1.59 g/cm³ Flame Resistance. CSA C22-2: Yes Operating Temperature Limit: 145°C Operating Temperature, IEC 216: 110°C
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: VAMPAMID 6 3025 V0, VAMPAMID , VAMPAMID63025V0, 6 3025 V 0, 6 3025 V0, 63025, 3025V, V0, 63025V0, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, Vamp Tech, Polyamide6, Nylon6, 30256
Generic Name
Generic Name may also be described by the following terms: PA6.
Features
Features may also be described by the following terms: Good Electrical Properties, Good Dimensional Stability, Dimensionally Stable.

Injection	Nominal Value	Unit
Drying Temperature		°F
Rear Temperature		°F
Mold Temperature		°F

Notes

¹Typical properties: these are not to be construed as specifications.

²Rate A (50°C/h)

³Rate B (120°C/h)

VAMPAMID 6 3025 V0

Polyamide 6

Mineral Filler

Supplied by Vamp Tech