SABIC HDPE M40053CO SABIC Polyethylene, High Density

Product Description

SABIC® HDPE M40053CO is extremely impact resistant, even at low temperatures. This grade is developed for production of caps where good organoleptic properties are required.

The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/medical applications.

General

Material Status

Commercial: Active

Availability

Europe

Features

Good Impact Resistance

Good Organoleptic Properties

Low Temperature Impact Resistance

Uses

Caps

Agency Ratings

Appearance

Natural Color

Forms

Pellets

Processing Method

Injection Molding

Physical	Nominal Value	Unit	Test Method
Density		g/cm³	ISO 1183
Melt Mass-Flow Rate (MFR)			ISO 1133
190°C/2.16 kg		g/10 min
190°C/5.0 kg		g/10 min
Melt Volume-Flow Rate (MVR)			ISO 1133
190°C/2.16 kg		in³/10min
190°C/5.0 kg		in³/10min
Environmental Stress-Cracking Resistance² (140°F, 0.118 in, Rhodacal-DS10)		hr	Internal Method
Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus (0.0787 in, Compression Molded)		psi	ISO 527-2/1BA/1
Tensile Stress			ISO 527-2/1BA/50
Yield, 0.0787 in, Compression Molded		psi
Break, 0.0787 in, Compression Molded		psi
Tensile Strain (Break, 0.0787 in, Compression Molded)		%	ISO 527-2/1BA/50
Tensile Creep Modulus			ISO 899-1
1 hr		psi
1000 hr		psi
Impact	Nominal Value	Unit	Test Method
Notched Izod Impact Strength			ISO 180/1A
-22°F		ft·lb/in²
73°F		ft·lb/in²
Hardness	Nominal Value	Unit	Test Method
Shore Hardness (Shore D, Compression Molded)			ISO 868
Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature (66 psi, Unannealed)		°F	ISO 75-2/B
Vicat Softening Temperature		°F	ISO 306/A
Melting Temperature		°F	DIN 53765
Enthalpy Change		J/g	DIN 53765
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® HDPE M40053CO, SABIC HDPE M40053CO, SABIC® HDPE , SABIC HDPE, SABICHDPEM40053CO, SABICHDPE, HDPEM 40053 CO, HDPEM40053CO, HDPEM40053, HDPE, M 40053 CO, M40053CO, M40053, 40053CO, Polyethylene, High Density, Polyethylene High Density, Polyethylene, PE, SABIC, PolyethyleneHighDensity, 40053M, 40053HDPEM
Features
Features may also be described by the following terms: Good Organoleptic Properties, Low Temperatuer Impact Resistance, Low Temp Impact Resistance, Good Impact Resistance.
Uses
Uses may also be described by the following terms: Closure Caps, Caps, Cap.
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1), EEC (1).

Notes

¹Typical properties: these are not to be construed as specifications.

²2 MPa

SABIC® HDPE M40053CO

High Density Polyethylene

Supplied by Saudi Basic Industries Corporation (SABIC)