IDES Prospector Already have an account? Login Here

IDES

SABIC® LDPE 2404AF00

Low Density Polyethylene

Supplied by Saudi Basic Industries Corporation (SABIC)

The technical datasheet with complete property values for SABIC® LDPE 2404AF00 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Discontinued
Availability 
  • Europe
Features 
  • Good Adhesion
  • Good Drawdown
  • Low Gel
  • Low Neck-In
  
Uses 
  • Coating Applications
Agency Ratings 
 
Forms 
  • Pellets
Processing Method 
  • Extrusion Coating
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Environmental Stress-Cracking Resistance 2 (140°F, 0.0787 in, Compression Molded)
hr
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress     ISO 527-2/200
Yield, 0.0630 in, Compression Molded
psi
  
Break, 0.0630 in, Compression Molded
psi
  
Tensile Strain (Break, 0.0630 in, Compression Molded)
%
 ISO 527-2/200
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Stress     ISO 527-3
MD: Yield, 0.98 mil
psi
  
TD: Yield, 0.98 mil
psi
  
MD: 0.98 mil
psi
  
TD: 0.98 mil
psi
  
Tensile Elongation     ISO 527-3
MD: Break, 0.98 mil
%
  
TD: Break, 0.98 mil
%
  
Water Vapor Transmission Rate (100°F, 0.98 mil, 100% RH)
g/100 in²/24 hr
 Internal Method
Oxygen Permeability 3 (73°F, 1.0 mil)
cm³/cm²/bar/24 hr
 Internal Method
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306
Melting Temperature (DSC)
°F
 DIN 53765
Enthalpy Change
J/g
 DIN 53765
Additional Information
Nominal Value
Unit
Test Method
Flexural Crack Resistance (1.0 mil)
cycles/10 holes
 Internal Method
Tear Strength     ISO 6383-2
MD: 1.0 mil
lbf/in
  
TD: 1.0 mil
lbf/in
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® LDPE 2404AF00, SABIC LDPE 2404AF00, SABIC® LDPE , SABIC LDPE, SABICLDPE2404AF00, SABICLDPE, LDPE 2404 AF 00, LDPE2404AF00, LDPE2404, LDPE, 2404 AF 00, 2404AF00, 2404AF, AF00, Polyethylene, Low Density, Polyethylene Low Density, Polyethylene, PE, SABIC, PolyethyleneLowDensity, AF2404, 2404LDPE
Features
Features may also be described by the following terms: Low Gel, Good Drawdown, Good draw down, Good Adhesion, Low Neck-in, Low Neck In.
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1), EEC (1).
Notes
1Typical properties: these are not to be construed as specifications.
22 MPa
30% RH
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.