IDES Prospector Already have an account? Login Here

IDES

SABIC® LDPE 1965T

Low Density Polyethylene

Supplied by Saudi Basic Industries Corporation (SABIC)

The technical datasheet with complete property values for SABIC® LDPE 1965T is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
SABIC® LDPE 1965T is an additive free standard CTR® tubular grade for masterbatch with a low viscosity. This grade has a very high filler acceptance.

SABIC® LDPE 1965T is a masterbatch grade typically for injection moulding applications, where high filler acceptance and good flow properties are required.

SABIC® LDPE 1965T is an extremely fast flowing polymer for flexible articles where mechanical properties are not critical. The material has a very low tendency to warp.

The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/
medical applications.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Good Flow
  • Low Viscosity
  • Low Warpage
Uses 
  • Masterbatch
Agency Ratings 
 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR)     ISO 1133
190°C/2.16 kg
g/10 min
  
190°C/5.0 kg
g/10 min
  
Melt Volume-Flow Rate (MVR)     ISO 1133
190°C/2.16 kg
in³/10min
  
190°C/5.0 kg
in³/10min
  
Environmental Stress-Cracking Resistance 2 (140°F, 0.118 in, Rhodacal-DS10)
hr
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus (0.0787 in, Compression Molded)
psi
 ISO 527-2/1BA/50
Tensile Stress     ISO 527-2/1BA/50
Yield, 0.0787 in, Compression Molded
psi
  
Break, 0.0787 in, Compression Molded
psi
  
Tensile Strain (Break, 0.0787 in, Compression Molded)
%
 ISO 527-2/1BA/50
Tensile Creep Modulus     ISO 899-1
1 hr
psi
  
1000 hr
psi
  
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact Strength     ISO 180/1A
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore D)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (66 psi, Unannealed)
°F
 ISO 75-2/B
Vicat Softening Temperature
°F
 ISO 306/A
Melting Temperature
°F
 DIN 53765
Enthalpy Change
J/g
 DIN 53765
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® LDPE 1965T, SABIC LDPE 1965T, SABIC® LDPE , SABIC LDPE, SABICLDPE1965T, SABICLDPE, LDPE 1965 T, LDPE1965T, LDPE1965, LDPE, 1965 T, 1965T, Polyethylene, Low Density, Polyethylene Low Density, Polyethylene, PE, SABIC, PolyethyleneLowDensity, T1965, 1965LDPE
Features
Features may also be described by the following terms: Good Flow, Low Warpage, Low Warp, Low Viscosity.
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1), EEC (1).
Notes
1Typical properties: these are not to be construed as specifications.
22 MPa
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.