IDES Prospector Already have an account? Login Here

IDES

SABIC® LLDPE 726Q

Linear Low Density Polyethylene

Supplied by Saudi Basic Industries Corporation (SABIC)

The technical datasheet with complete property values for SABIC® LLDPE 726Q is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
SABIC® LLDPE 726Q is a fractional melt index, butene-linear low density polyethylene resin. This grade is designed to give blown films a relatively high stiffness and a good overall balance of other performance properties. This material contains anti block, slip erucamide and processing aid.

Applications for SABIC® LLDPE 726Q are shipping sacks, produce bags, bread bags, can liners and carrier bags.

The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/medical applications.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Antiblock (750 ppm)
  • Antioxidant
  • Processing Aid
  • Slip (1250 ppm)
  
Features 
  • Antiblocking
  • Antioxidant
  • Food Contact Acceptable
  • Good Impact Resistance
  • Good Stiffness
  • Heat Sealable
  • Puncture Resistant
  • Slip
Uses 
  • Bags
  • Film
  • Liners
Forms 
  • Pellets
Processing Method 
  • Blown Film
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183/A
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Coefficient of Friction
 
 ISO 8295
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Modulus
     ISO 527-3
MD: 2.0 mil, Blown Film
psi
  
TD: 2.0 mil, Blown Film
psi
  
Tensile Stress
     ISO 527-3
MD: Yield, 2.0 mil, Blown Film
psi
  
TD: Yield, 2.0 mil, Blown Film
psi
  
MD: 2.0 mil, Blown Film
psi
  
TD: 2.0 mil, Blown Film
psi
  
Tensile Elongation
     ISO 527-3
MD: Break, 2.0 mil, Blown Film
%
  
TD: Break, 2.0 mil, Blown Film
%
  
Elmendorf Tear Strength
     ISO 6383-2
MD: 2.0 mil 2
lbf/in
  
TD: 2.0 mil 3
lbf/in
  
Impact
Nominal Value
Unit
Test Method
Impact Strength - Blown Film (2.0 mil)
ft·lb/in
 ASTM D4272
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/A
Melting Temperature (DSC)
°F
 Internal Method
Optical
Nominal Value
Unit
Test Method
Gloss (45°, 1.97 mil, Blown Film)
 
 ASTM D2457
Haze (1.97 mil, Blown Film)
%
 ASTM D1003
Clarity
V
 Internal Method
Additional Information
Nominal Value
Unit
Test Method
Blocking
g
 Internal Method
Puncture Resistance - Blown Film (2.0 mil)
ft·lb/in
 Internal Method
Re-blocking
g
 Internal Method
Film of 50 µm and BUR=2 has been produced on Kiefel IBC with 130 kg/h. Die size 200 mm, die gap 0.8 mm.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® LLDPE 726Q, SABIC LLDPE 726Q, SABIC® LLDPE , SABIC LLDPE, SABICLLDPE726Q, SABICLLDPE, LLDPE 726 Q, LLDPE726Q, LLDPE726, LLDPE, 726 Q, 726Q, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, Polyethylene, PE, SABIC, PolyethyleneLinearLowDensity, Q726, 726LLDPE
Features
Features may also be described by the following terms: Good Stiffness, Slip, Unspecified Slip, Good Puncture Resistance, Puncture Resistant, Good Impact Resistance, Antiblocking, Unspecified Antiblock.
Notes
1Typical properties: these are not to be construed as specifications.
2Blown FIlm
3Blown Film
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.