IDES Prospector Already have an account? Login Here

IDES

WPP PP PPC3220 UV Black

Polypropylene Copolymer

Supplied by Washington Penn Plastic Co. Inc.

The technical datasheet with complete property values for WPP PP PPC3220 UV Black is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Copolymer
  • Good Impact Resistance
  • Good Stiffness
  • Good UV Resistance
  • Medium Flow
Uses 
  • Automotive Applications
  • Automotive Interior Trim
  
Automotive Specifications 
Appearance 
  • Black
  • Colors Available
  
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield)
psi
 ASTM D638
Flexural Modulus - Tangent
psi
 ASTM D790
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
Additional Information
Dart Impact, GM 9300P, -30°C, 3.4 m/s: 65J
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: WPP PP PPC3220 UV Black, WPP PP , WPPPPPPC3220UVBlack, WPPPP, PPPPC 3220 UV Black, PPPPC3220 UV Black, PPPPC3220, PP, PPC 3220 UV Black, PPPPC3220UVBlack, PPC3220 UV Black, PPC3220, 3220UV, UVBlack, PPC3220UVBlack, Polypropylene Copolymer, PP Copolymer, Polypropylene, Washington Penn, PolypropyleneCopolymer, PPCopolymer, 3220PPC, 3220PPPPC
Features
Features may also be described by the following terms: Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant, Good Stiffness, Medium Flow, Medium Melt, Medium MFI, Good Impact Resistance.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
Automotive Specifications
This plastic material has approval for 2 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): GM (1), CHRYSLER (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Holding Pressure
psi
  
Back Pressure
psi
  
Clamp Tonnage
tons/in²
  
Cushion
in
  
Injection Notes
Injection Speed: 1.5 to 2.5 in/s
Zone 4 Temperature: 420 to 430°F
Hot Runner Temperature: 410 to 440°F
Hydraulic Oil Temperature: 110 to 125°F
Shot Capacity vs. Barrel Capacity: 2.5 to 4
Screw Decompression: 0.1 to 0.25 in
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.