IDES Prospector Already have an account? Login Here

IDES

SABIC® LLDPE M500026

Linear Low Density Polyethylene

Supplied by Saudi Basic Industries Corporation (SABIC)

The technical datasheet with complete property values for SABIC® LLDPE M500026 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
SABIC® LLDPE M500026 is a high flow, linear low density polyethylene copolymer injection moulding grade with a narrow molecular weight distribution. It has been designed to have excellent low temperature toughness, stress crack resistance (ESCR), mouldability and gloss.

SABIC® LLDPE M500026 is recommended for injection moulding of containers and reclosure lids. It is well suited for fast cycle, deep draw injection moulding applications, which takes advantage of its high flow properties. Also, the higher melting point of the material allows for high end-use temperature when compared with conventional polyehtylenes of equal density. SABIC® LLDPE M500026 resin is recommended for injection moulding masterbatch where a high filler acceptance is required, combined with a good flow.

The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/medical applications.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Fast Molding Cycle
  • High ESCR (Stress Crack Resist.)
  • High Flow
  • High Gloss
  • Low Temperature Toughness
  • Narrow Molecular Weight Distribution
Uses 
  • Containers
  • Lids
  • Masterbatch
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Environmental Stress-Cracking Resistance (100% Igepal, Compression Molded, F50)
hr
 ASTM D1693A
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus - 1% Secant (Compression Molded)
psi
 ASTM D638
Tensile Strength
     ASTM D638
Yield, Compression Molded
psi
  
Break, Compression Molded
psi
  
Tensile Elongation (Break, Compression Molded)
%
 ASTM D638
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (Compression Molded)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D, Compression Molded)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Brittleness Temperature
°F
 ASTM D746
Vicat Softening Temperature
°F
 ASTM D1525 2
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® LLDPE M500026, SABIC LLDPE M500026, SABIC® LLDPE , SABIC LLDPE, SABICLLDPEM500026, SABICLLDPE, LLDPEM 500026, LLDPEM500026, LLDPE, M 500026, M500026, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, Polyethylene, PE, SABIC, PolyethyleneLinearLowDensity, 500026M, 500026LLDPEM
Features
Features may also be described by the following terms: Low Temperature Toughness, Narrow Molecular Weight Distribution, Narrow MW Distribution, High Flow, High Melt, High MFI, High Gloss, High Environmental Stress Cracking Resistance, High ESCR, Stress Cracking Resistant, Fast Cycle, Rapid Cycle, Productivity, Fast Molding Cycle.
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Rate A (50°C/h), Loading 1 (10 N)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.