Alkatuff® LL711UV Qenos Polyethylene, Linear Low Density

Product Description

Alkatuff LL711UV is a hexene LLDPE material specifically designed for rotational moulding applications that require excellent ESCR, chemical resistance, stiffness and toughness. Alkatuff LL711UV is UV stabilized to provide prolonged outdoor protection in Australian conditions.

Application:
Alkatuff LL711UV is designed for chemical and water tanks and other applications where toughness, stiffness and UV protection is important.

Specifications:
Alkatuff LL711UV complies with the base resin requirements of AS/NZS 4766 Polyethylene storage tanks for water and chemicals.

If this product is used for food contact applications, then the user needs to ensure compliance with the requirements of AS2070-1999 and relevant FDA regulations.

When used in accordance with FDA application guidelines, this product meets the requirements of FDA 21 CFG 177.1520 (c) 3.1a and AS2070-1999 section 4.1.1(a). This product contains UV light stabilizers and so end use restrictions as described in FDA 21 CFR 176.170 (c) table 2 conditions D to G apply. Volume and food type restrictions may apply. This product should not be used in applications for holding food during cooking without the required compliance testing. This information is only for the Major End Use described on this Product Data sheet. For further information, please contact your primary Qenos contact.

General

Material Status

Commercial: Active

Availability

Asia Pacific

Additive

UV Stabilizer

Features

Food Contact Acceptable

Good Chemical Resistance

Good Stiffness

Good Toughness

Good UV Resistance

High ESCR (Stress Crack Resist.)

Uses

Outdoor Applications

Tanks

Agency Ratings

Processing Method

Rotational Molding

Physical	Nominal Value	Unit	Test Method
Density		g/cm³	ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)		g/10 min	ASTM D1238
Environmental Stress-Cracking Resistance (10% Igepal, F50)		hr	ASTM D1693A
Mechanical	Nominal Value	Unit	Test Method
Tensile Strength³ (Yield)		psi	ASTM D638
Flexural Modulus - 1% Secant		psi	ASTM D790
Hydrostatic Design Basis⁴		psi	ASTM D2837
Thermal	Nominal Value	Unit	Test Method
Peak Melting Temperature		°F	ASTM D3418
Thermal Stability			AS/NZS 4766
Additional Information	Nominal Value	Unit	Test Method
Drinking Water Contact			AS/NZS 4020
UV Protection			ASTM D2565
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Alkatuff® LL711UV, Alkatuff LL711UV, Alkatuff® , Alkatuff, AlkatuffLL711UV, LL 711 UV, LL711UV, LL711, 711UV, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, LLDPE, Polyethylene, PE, Qenos, PolyethyleneLinearLowDensity, 711LL
Features
Features may also be described by the following terms: Good Chemical Resistance, Chemical Resistant, Good Toughness, Tough, Good Stiffness, High Environmental Stress Cracking Resistance, High ESCR, Stress Cracking Resistant, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
Agency Ratings
This plastic material has 4 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): AS (1), FDA (2), AS/NZS (1).

Notes

¹Conditions D through G apply. Volume and food type restrictions may apply.

²Typical properties: these are not to be construed as specifications.

³2.0 in/min

⁴A service factor must be applied in accordance with AS/NZS 4766.

Alkatuff® LL711UV

Linear Low Density Polyethylene

Supplied by Qenos Pty Ltd