IDES Prospector Already have an account? Login Here

IDES

Halene L 71602W

Linear Low Density Polyethylene

Supplied by Haldia Petrochemicals Ltd.

The technical datasheet with complete property values for Halene L 71602W is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
71602W is a LLDPE film grade produced by Spherilene Technology.

71602W is without Slip additives and Antiblock and can be used in Packaging Film Applications.

The precise morphological control achieved during polymerization confers good processability and mechanical strengths.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Features 
  • Good Processability
  • Good Strength
  
Uses 
  • Film
  • Laminates
  • Packaging
Forms 
  • Pellets
Processing Method 
  • Blown Film
Physical
Nominal Value
Unit
Test Method
Density 2
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Strength 3
     ASTM D882
MD: Yield, 0.98 mil, Blown Film
psi
  
TD: Yield, 0.98 mil, Blown Film
psi
  
MD: Break, 0.98 mil, Blown Film
psi
  
TD: Break, 0.98 mil, Blown Film
psi
  
Tensile Elongation 3
     ASTM D882
MD: Break, 0.98 mil, Blown Film
%
  
TD: Break, 0.98 mil, Blown Film
%
  
Dart Drop Impact 4 (0.98 mil, Blown Film)
g
 ASTM D1709A
Elmendorf Tear Strength
     ASTM D1922
MD: 0.98 mil, Blown Film
g
  
TD: 0.98 mil, Blown Film
g
  
Additional Information
Die gap: 2.5 mm
BUR: 2.5
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Halene L 71602W, Halene L , HaleneL71602W, HaleneL, L 71602 W, L71602W, L71602, 71602 W, 71602W, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, LLDPE, Polyethylene, PE, Haldia Petrochem, PolyethyleneLinearLowDensity, W71602, 71602L
Features
Features may also be described by the following terms: Good Processability, Easy Processing, Good Strength.
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Melt Temperature
°F
  
Extrusion Notes
Blow up Ratio: 2.0 to 3.0
Die Gap: 2.0 to 2.5 mm
Notes
1Typical properties: these are not to be construed as specifications.
223°C
320 in/min
438 mm Dart, 66 cm Height
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.