IDES Prospector Already have an account? Login Here

IDES

Daplen™ EC211T

Polypropylene

Mineral Filler, 20%

Supplied by Borealis AG

The technical datasheet with complete property values for Daplen™ EC211T is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Daplen EC211T is a mineral reinforced, elastomer modified PP compound, intended for injection moulding. The product is available in black (Daplen EC211T-8229).

Daplen EC211T provides high stiffness required for injection moulded interior trims.

The product is UV stabilised.

Daplen EC211T gives sufficient paintability by use of adhesive primers alone or by use of other pretreatments.

Injection moulded exterior or interior trims i.e.
  • Air-distribution panels
  • Lower lateral protection
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
  • North America
  • South America
Filler / Reinforcement 
  • Mineral Filler, 20% Filler by Weight
Additive 
  • UV Stabilizer
Features 
  • High Stiffness
  • Paintable
  • Recyclable Material
Uses 
  • Automotive Applications
  • Automotive Interior Parts
  • Automotive Interior Trim
Appearance 
  • Black
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR)
     ISO 1133
230°C/2.16 kg
g/10 min
  
230°C/5.0 kg
g/10 min
  
Molding Shrinkage
%
 ISO 294-4
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus (Injection Molded)
psi
 ISO 527-2/1
Tensile Stress (Yield, Injection Molded)
psi
 ISO 527-2/50
Tensile Strain (Yield, Injection Molded)
%
 ISO 527-2/50
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact Strength (-40°F)
ft·lb/in²
 ISO 180/1A
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore D, Injection Molded)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/A50
Additional Information
The value listed as Molding Shrinkage, ISO 294-4, was tested in accordance with Borealis test methods.
Paint Adhesion, Peel Test: 12 N/15 mm
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Daplen™ EC211T, Daplen EC211T, Daplen™ , Daplen, DaplenEC211T, EC 211 T, EC211T, EC211, 211T, Polypropylene, Unspecified, Polypropylene Unspecified, PP, Unspecified, PP Unspecified, Polypropylene, PP, Borealis, PolypropyleneUnspecified, PPUnspecified, 211EC
Generic Name
Generic Name may also be described by the following terms: Polypropilene, Polypropelene.
Features
Features may also be described by the following terms: High Stiffness.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Injection Notes
Screw Speed: slow to medium
Holding Pressure: 50 to 70% of the injection pressure
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.