IDES Prospector Already have an account? Login Here

IDES

Daplen™ ED188AI

Polypropylene

Mineral Filler, 15%

Supplied by Borealis AG

The technical datasheet with complete property values for Daplen™ ED188AI is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
ED188AI is a 15% mineral filled PP / EPDM grade intended for injection moulding.

ED188AI has been developed especially for the car industry, to be used in interior parts where high scratch resistance is a necessity.

ED188AI offers very good balance in stiffness/impact strength and has excellent scratch resistance.

Applications include:
  • dashboards
  • pillar trims
  • door panels/pockets
  • other automotive interior parts
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Filler / Reinforcement 
  • Mineral Filler, 15% Filler by Weight
Features 
  • Good Impact Resistance
  • Good Stiffness
  • Recyclable Material
  • Scratch Resistant
  
Uses 
  • Automotive Applications
  • Automotive Instrument Panel
  • Automotive Interior Parts
  • Automotive Interior Trim
  
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR)
     ISO 1133
230°C/2.16 kg
g/10 min
  
230°C/5.0 kg
g/10 min
  
Molding Shrinkage
%
 ISO 294-4
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield)
psi
 ISO 527-2/50
Tensile Strain (Yield)
%
 ISO 527-2/50
Flexural Modulus 2
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1
-4°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
     ISO 179/1U
-4°F
ft·lb/in²
  
73°F
 
  
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (66 psi, Unannealed)
°F
 ISO 75-2/B
Vicat Softening Temperature
°F
 ISO 306/B50
Additional Information
The value listed as Molding Shrinkage, ISO 294-4, was tested in accordance with Borealis test methods.
Fogging, DIN 75201, 100°C, 16 hr: 0.98 mg
Emission, VDA 277: 28 µg C/g
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Daplen™ ED188AI, Daplen ED188AI, Daplen™ , Daplen, DaplenED188AI, ED 188 AI, ED188AI, ED188, 188AI, Polypropylene, Unspecified, Polypropylene Unspecified, PP, Unspecified, PP Unspecified, Polypropylene, PP, Borealis, PolypropyleneUnspecified, PPUnspecified, 188ED
Generic Name
Generic Name may also be described by the following terms: Polypropilene, Polypropelene.
Features
Features may also be described by the following terms: Good Stiffness, Scratch Resistant, Resists Scratches, Good Impact Resistance.
Uses
Uses may also be described by the following terms: Automotive Instrument Panel, Automotive Dash Board, Automotive Applications, Automotive Sector.
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Injection Notes
Holding Pressure: 50 to 70% of the injection pressure
Notes
1Typical properties: these are not to be construed as specifications.
20.079 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.