IDES Prospector Already have an account? Login Here

IDES

Aegis® PL75HS

Polyamide 6

Supplied by Honeywell

The technical datasheet with complete property values for Aegis® PL75HS is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Aegis PL75HS is a medium viscosity, heat stabilized, flexible nylon 6 especially suited to the production of extrusion profiles offering a combination of good flexibility, toughness and abrasion resistance. Chemical resistance is excellent to greases, oils and hydrocarbons.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Additive 
  • Heat Stabilizer
Features 
  • Good Abrasion Resistance
  • Good Chemical Resistance
  • Good Flexibility
  • Good Toughness
  • Grease Resistant
  • Heat Stabilized
  • Hydrocarbon Resistant
  • Medium Viscosity
  • Oil Resistant
Uses 
  • Profiles
Forms 
  • Pellets
Processing Method 
  • Profile Extrusion
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield, 73°F)
psi
 ASTM D638, ISO 527-2
Tensile Elongation
      
Break, 73°F
%
 ASTM D638
Break, 73°F
%
 ISO 527-2
Flexural Modulus (73°F)
psi
 ASTM D790, ISO 178
Flexural Strength (73°F)
psi
 ASTM D790, ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
      
73°F
ft·lb/in
 ASTM D256
73°F
ft·lb/in²
 ISO 180
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
Melting Temperature (DSC)
°F
 ISO 3146
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Aegis® PL75HS, Aegis PL75HS, Aegis® , Aegis, AegisPL75HS, PL 75 HS, PL75HS, PL75, 75HS, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, Honeywell, Polyamide6, Nylon6, 75PL
Generic Name
Generic Name may also be described by the following terms: PA6.
Features
Features may also be described by the following terms: Medium Viscosity, Heat Stabilized, Heat-ageing Stabilized, Heat Ageing Stabilized, Heat-aging Stabilized, Heat Aging Stabilized, Good Flexibility, Flexible, Good Toughness, Tough, Good Abrasion Resistance, Abrasion Resistant, Good Chemical Resistance, Chemical Resistant.
Extrusion
Nominal Value
Unit
 
Drying Temperature
°F
  
Suggested Max Moisture
%
  
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Melt Temperature
°F
  
Die Temperature
°F
  
Extrusion Notes
Screw Parameters:
  • Metering section: 40%
  • Transition section: 3 to 4 flights
  • Feed section: balance of screw length
  • Compression ratio: 3.5:1 to 4.0:1
  • L/D ratio: 20:1 to 24:1
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.