IDES Prospector Already have an account? Login Here

IDES

Aegis® H100MP

Polyamide 6

Supplied by Honeywell

The technical datasheet with complete property values for Aegis® H100MP is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Aegis® H100MP is a lubricated and nucleated medium viscosity nylon 6 extrusion grade homopolymer for cast or blown film. It conforms to FDA requirements of 21 CFR 177.1500 as well as EU Directive 2002/72/EC. It possesses the combination of strength, toughness and thermoforming properties associated with nylon 6 as well as excellent heat, chemical, and abrasion resistance.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Additive 
  • Lubricant
  • Nucleating Agent
  
Features 
  • Good Abrasion Resistance
  • Good Chemical Resistance
  • Good Strength
  • Good Toughness
  • High Heat Resistance
  • Homopolymer
  • Lubricated
  • Medium Viscosity
  • Nucleated
Uses 
  • Cast Film
  • Packaging
  
Agency Ratings 
 
Forms 
  • Pellets
Processing Method 
  • Blown Film
  • Cast Film
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (235°C/1.0 kg)
g/10 min
 ASTM D1238
Water Absorption     ASTM D570
24 hr
%
  
Saturation
%
  
Equilibrium
%
  
Films
Nominal Value
Unit
Test Method
Oxygen Permeability
cm³·mil/100in²/atm/24 hr
 ASTM D3985
Thermal
Nominal Value
Unit
Test Method
Melting Temperature
°F
  
Additional Information
FAV, ASTM D789: 100
96% SAV: 3.35
Nitrogen Permeability: 14 (0.903) cc/m²/day (cc/100in²/day)
Carbon Dioxide Permeability: 72.8 (4.697) cc/m²/day (cc/100in²/day)
Extractible Content: 0.7 %
Moisture Content: 0.08 %
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Aegis® H100MP, Aegis H100MP, Aegis® , Aegis, AegisH100MP, H 100 MP, H100MP, H100, 100MP, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, Honeywell, Polyamide6, Nylon6, 100H
Generic Name
Generic Name may also be described by the following terms: PA6.
Features
Features may also be described by the following terms: Medium Viscosity, Good Strength, Good Toughness, Tough, High Heat Resistance, Good Chemical Resistance, Chemical Resistant, Good Abrasion Resistance, Abrasion Resistant.
Uses
Uses may also be described by the following terms: Cast Film.
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1), EU (1).
Extrusion
Nominal Value
Unit
 
Drying Temperature
°F
  
Suggested Max Moisture
%
  
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Adapter Temperature
°F
  
Melt Temperature
°F
  
Die Temperature
°F
  
Extrusion Notes
The values listed above in Extrusion are for cast film.

Typical Barrel Profile for Tubular (Blown) Films:
  • Barrel Temperature: 246 to 254°C (474 to 490°F)
  • Adapter Temperature: 260°C (500°F)
  • Die Temperature: 254°C (490°F)
  • Processing Melt Temperature: 254 to 260°C (490 to 500°F)

Screw Parameters:
  • Metering section: 40%
  • Transition section: 3 to 4 flights
  • Feed section balance of screw length
  • Compression ratio: 3.5:1 to 4.0:1
  • L/D ratio: 24:1
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.