|
Density
|
|
g/cm³
|
ISO 1183 |
|
Melt Volume-Flow Rate (MVR)
|
|
|
ISO 1133 |
|
340°C/5.0 kg
|
|
in³/10min
|
|
|
360°C/5.0 kg
|
|
in³/10min
|
|
|
Water Absorption
|
|
|
ISO 62 |
|
Saturation, 73°F
|
|
%
|
|
|
Equilibrium, 73°F, 50% RH
|
|
%
|
|
|
Tensile Modulus
|
|
psi
|
ISO 527-2/1 |
|
Tensile Stress
|
|
|
ISO 527-2/50 |
|
Yield
|
|
psi
|
|
|
Break
|
|
psi
|
|
|
Tensile Strain
|
|
|
ISO 527-2/50 |
|
Yield
|
|
%
|
|
|
Break
|
|
%
|
|
|
Flexural Modulus 2
|
|
psi
|
ISO 178 |
|
Flexural Strength 2, 3
|
|
psi
|
ISO 178 |
|
Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel)
|
|
mg
|
Internal Method |
|
Charpy Notched Impact Strength 4 (73°F)
|
|
ft·lb/in²
|
ISO 179/1eA |
|
Notched Izod Impact Strength 5
|
|
|
ISO 180/1A |
|
-22°F
|
|
ft·lb/in²
|
|
|
73°F
|
|
ft·lb/in²
|
|
|
Unnotched Izod Impact Strength 5
|
|
|
ISO 180/1U |
|
-22°F
|
|
|
|
|
73°F
|
|
|
|
|
Ball Indentation Hardness (H 358/30)
|
|
psi
|
ISO 2039-1 |
|
Heat Deflection Temperature 6
|
|
|
|
|
66 psi, Unannealed, 3.94 in Span
|
|
°F
|
ISO 75-2/Be |
|
264 psi, Unannealed, 3.94 in Span
|
|
°F
|
ISO 75-2/Ae |
|
Vicat Softening Temperature
|
|
|
|
|
--
|
|
°F
|
ISO 306/A50 |
|
--
|
|
°F
|
ISO 306/B50 |
|
--
|
|
°F
|
ISO 306/B120 |
|
Ball Pressure Test (257°F)
|
|
|
IEC 60695-10-2 |
|
CLTE
|
|
|
ISO 11359-2 |
|
Flow: 73 to 302°F
|
|
in/in/°F
|
|
|
Transverse: 73 to 302°F
|
|
in/in/°F
|
|
|
Thermal Conductivity
|
|
Btu·in/hr/ft²/°F
|
ISO 8302 |
|
Surface Resistivity
|
|
ohms
|
IEC 60093 |
|
Volume Resistivity
|
|
ohm·cm
|
IEC 60093 |
|
Relative Permittivity
|
|
|
IEC 60250 |
|
50 Hz
|
|
|
|
|
60 Hz
|
|
|
|
|
1 MHz
|
|
|
|
|
Dissipation Factor
|
|
|
IEC 60250 |
|
50 Hz
|
|
|
|
|
60 Hz
|
|
|
|
|
1 MHz
|
|
|
|
|
2.45 GHz
|
|
|
|
|
Comparative Tracking Index
|
|
|
IEC 60112 |
|
--
|
|
V
|
|
|
Solution B
|
|
V
|
|
|
Electric Strength
|
|
|
IEC 60243-1 |
|
0.0315 in, in Oil
|
|
V/mil
|
|
|
0.0630 in, in Oil
|
|
V/mil
|
|
|
0.126 in, in Oil
|
|
V/mil
|
|
|
Oxygen Index
|
|
%
|
ISO 4589-2 |
|
RTI Elec
|
|
°F
|
UL 746 |
|
This supplier and product may also be known by these terms: GE Plastics Europe, LNP Engineering Plastics, GE Polymerland Europe, GE Polymerland, GE Plastics
Product names can be difficult to match. You may have searched any one of these terms to find this product: ULTEM* 1010X Resin, ULTEM 1010X Resin, ULTEM* , ULTEM, ULTEM1010XResin, 1010 X Resin, 1010X Resin, 1010X, XResin, 1010XResin, Polyether Imide, PEI, SABIC IP Euro, PolyetherImide, X1010
|
|
Features may also be described by the following terms: Good Flow, Zero Halogen Content, Halogen Free.
|
|
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): DIN (1).
|