IDES Prospector Already have an account? Login Here

IDES

DINALEN® 35

Low Density Polyethylene

Supplied by DIOKI d.d.

The technical datasheet with complete property values for DINALEN® 35 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
DINALEN® 35 is low density polyethylene containing additives. It is primarily intended for blow film extrusion while other processing techniques can be used to a lesser extent.

DINALEN® 35 exhibits excellent very good draw-down with good balance of stiffness, mechanical and optical properties of extruded film.

DINALEN® 35 is extruded at recommended melt temperature range between 165°C and 185°C.

Recommended film thickness: 0.030 mm to 0.100 mm.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Antiblock
  • Slip
  
Features 
  • Antiblocking
  • Food Contact Acceptable
  • Good Processability
  • High Gloss
  • Slip
Uses 
  • Bags
  • Blending
  • Film
  • General Purpose
  • Laminates
  • Packaging
Agency Ratings 
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Blown Film
  • Film Extrusion
  
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus (Compression Molded)
psi
 ISO 527-2/200
Tensile Stress
     ISO 527-2/200
Yield, Compression Molded
psi
  
Break, Compression Molded
psi
  
Tensile Strain (Break, Compression Molded)
%
 ISO 527-2/200
Coefficient of Friction
     ISO 8295
vs. Itself - Dynamic
 
  
vs. Itself - Static
 
  
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Film Thickness - Recommended / Available
 
  
Tensile Strength
     ISO 527-3/500
MD: 2.0 mil, Blown Film
psi
  
TD: 2.0 mil, Blown Film
psi
  
Tensile Elongation
     ISO 527-3/500
MD: Break, 2.0 mil, Blown Film
%
  
TD: Break, 2.0 mil, Blown Film
%
  
Dart Drop Impact (2.0 mil, Blown Film)
g
 ISO 7765-1
Trouser Tear Resistance 2
     ISO 6383-1
MD: 2.0 mil, Blown Film
lbf/in
  
TD: 2.0 mil, Blown Film
lbf/in
  
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore D, Compression Molded)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/A50
Melting Temperature
°F
 ISO 11357-3
Optical
Nominal Value
Unit
Test Method
Gloss
      
20°, 1.97 mil, Blown Film
 
  
60°, 1.97 mil, Blown Film
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: DINALEN® 35, DINALEN 35, DINALEN® , DINALEN, DINALEN35, 35, Polyethylene, Low Density, Polyethylene Low Density, LDPE, Polyethylene, PE, Dioki, PolyethyleneLowDensity
Features
Features may also be described by the following terms: Good Processability, Easy Processing, Slip, Unspecified Slip, Antiblocking, Unspecified Antiblock, High Gloss.
Agency Ratings
This plastic material has 8 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EC (1), EU (7).
Notes
1Typical properties: these are not to be construed as specifications.
27.9 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.