IDES Prospector Already have an account? Login Here

IDES

Latan® 23UV

Acetal (POM) Copolymer

Supplied by LATI S.p.A.

The technical datasheet with complete property values for Latan® 23UV is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Compound based on Polyoximethylene (POM).
UV stabilised.
Low viscosity. Very good tribological properties.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Additive 
  • UV Stabilizer
Features 
  • Good UV Resistance
  • Low Viscosity
  
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Molding Shrinkage 2
     ISO 294-4
Across Flow: 0.0787 in
%
  
Flow: 0.0787 in
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
     ISO 527-2/1
73°F
psi
  
140°F
psi
  
194°F
psi
  
Tensile Stress
     ISO 527-2/5
Yield, 73°F
psi
  
Yield, 140°F
psi
  
Yield, 194°F
psi
  
Break, 73°F
psi
  
Tensile Strain
     ISO 527-2/5
Yield, 73°F
%
  
Break, 73°F
%
  
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eA
Charpy Unnotched Impact Strength (73°F)
 
 ISO 179/1eU
Notched Izod Impact (73°F, 0.126 in)
ft·lb/in
 ASTM D256A
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B50
CLTE - Flow (86 to 212°F)
in/in/°F
 ASTM D696
Continuous Use Temperature 3
°F
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Latan® 23UV, Latan 23UV, Latan® , Latan, Latan23UV, 23 UV, 23UV, Acetal Copolymer, Acetal Copolymer, Acetal (POM) Copolymer, Acetal POM Copolymer, Acetal, pom, Lati, AcetalPOMCopolymer, UV23
Features
Features may also be described by the following terms: Low Viscosity, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Notes
1Typical properties: these are not to be construed as specifications.
2at 60 Mpa of cavity pressure
320000 hr
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.