IDES Prospector Already have an account? Login Here

IDES

LEXAN* 123HSR Resin

Polycarbonate

Supplied by SABIC Innovative Plastics Asia Pacific

The technical datasheet with complete property values for LEXAN* 123HSR Resin is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Easy flow, UV stabilised, super release grade polycarbonate.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Additive 
  • UV Stabilizer
Features 
  • Good Flow
  • Good Mold Release
  
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (300°C/1.2 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow (0.126 in)
in/in
 Internal Method
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2
psi
 ASTM D638
Tensile Strength 3
     ASTM D638
Yield
psi
  
Break
psi
  
Tensile Elongation 3
     ASTM D638
Yield
%
  
Break
%
  
Flexural Modulus 4 (1.97 in Span)
psi
 ASTM D790
Flexural Strength 4 (Yield, 1.97 in Span)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
264 psi, Unannealed, 0.126 in
°F
  
264 psi, Unannealed, 0.252 in
°F
  
Vicat Softening Temperature
°F
 ASTM D1525 5
CLTE - Flow (-40 to 140°F)
in/in/°F
 ASTM E831
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Constant
     ASTM D150
50 Hz
 
  
60 Hz
 
  
1 MHz
 
  
Dissipation Factor
     ASTM D150
50 Hz
 
  
60 Hz
 
  
1 MHz
 
  
Comparative Tracking Index
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0591 in)
 
 UL 94
UL
Nominal Value
Unit
Test Method
RTI Str
°F
 UL 746
RTI Imp
°F
 UL 746
RTI Elec
°F
 UL 746
Related Terminology
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics

Product names can be difficult to match. You may have searched any one of these terms to find this product: LEXAN* 123HSR Resin, LEXAN 123HSR Resin, LEXAN* , LEXAN, LEXAN123HSRResin, 123 HSR Resin, 123HSR Resin, 123HSR, HSRResin, 123HSRResin, Polycarbonate, PC, SABIC IP Asia, HSR123
Features
Features may also be described by the following terms: Good Mold Release, Easy Release, Good Demolding, Good Flow.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Drying Time, Maximum
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
22.0 in/min
3Type I, 2.0 in/min
40.051 in/min
5Rate B (120°C/h), Loading 2 (50 N)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.