IDES Prospector Already have an account? Login Here

IDES

NORYL GTX* GTX909 Resin

Polyphenylene Ether + PS + Nylon

Supplied by SABIC Innovative Plastics Asia Pacific

The technical datasheet with complete property values for NORYL GTX* GTX909 Resin is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
400F (205C) HDT. 3.3 Notched Izod. Excellent chemical resistance
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Features 
  • Good Chemical Resistance
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow (0.126 in)
in/in
 Internal Method
Water Absorption
     ASTM D570
24 hr
%
  
Equilibrium, 73°F
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2
     ASTM D638
Yield
psi
  
Break
psi
  
Tensile Elongation 2
     ASTM D638
Yield
%
  
Break
%
  
Flexural Modulus 3 (3.94 in Span)
psi
 ASTM D790
Flexural Strength 3 (Yield, 3.94 in Span)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
     ASTM D256
-22°F
ft·lb/in
  
73°F
ft·lb/in
  
Instrumented Dart Impact
     ASTM D3763
-22°F, Energy at Peak Load
in·lb
  
73°F, Energy at Peak Load
in·lb
  
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed, 0.252 in
°F
  
264 psi, Unannealed, 0.252 in
°F
  
Vicat Softening Temperature
°F
 ASTM D1525 4
CLTE
     ASTM E831
Flow: -4 to 302°F
in/in/°F
  
Transverse: -4 to 302°F
in/in/°F
  
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength (0.126 in, in Oil)
V/mil
 ASTM D149
Dielectric Constant
     ASTM D150
50 Hz
 
  
60 Hz
 
  
1 MHz
 
  
Dissipation Factor
     ASTM D150
50 Hz
 
  
60 Hz
 
  
1 MHz
 
  
Related Terminology
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics

Product names can be difficult to match. You may have searched any one of these terms to find this product: NORYL GTX* GTX909 Resin, NORYL GTX GTX909 Resin, NORYL GTX* , NORYL GTX, NORYLGTXGTX909Resin, NORYLGTX, GTX 909 Resin, GTX909 Resin, GTX909, 909Resin, GTX909Resin, Polyphenylene Ether + PS + Nylon, Polyphenylene Ether PS Nylon, Polyphenylene Ether : PS : Nylon, Polyphenylene Ether / PS / Nylon, Polyphenylene Ether - PS - Nylon, Polyphenylene Ether _ PS _ Nylon, Polyphenylene Ether PS Nylon, PPE+PS+Nylon, PPEPSNylon, PPE:PS:Nylon, PPE/PS/Nylon, PPE-PS-Nylon, PPE_PS_Nylon, PPE PS Nylon, Polyphenylene Ether, PPE, SABIC IP Asia, PolyphenyleneEtherPSNylon, PolyphenyleneEther, PolyphenyleneEther_PS_Nylon, 909GTX
Features
Features may also be described by the following terms: Good Chemical Resistance, Chemical Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Drying Time, Maximum
hr
  
Suggested Max Moisture
%
  
Suggested Shot Size
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Vent Depth
in
  
Injection Notes
Minimum Moisture Content: 0.02 %
Notes
1Typical properties: these are not to be construed as specifications.
2Type I, 2.0 in/min
30.10 in/min
4Rate B (120°C/h), Loading 2 (50 N)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.