IDES Prospector Already have an account? Login Here

IDES

Braskem PE BT-100K

High Density Polyethylene

Supplied by Braskem

The technical datasheet with complete property values for Braskem PE BT-100K is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
BT 100K is a HDPE High Molecular Weight (HMW) monomodal copolymer. Containers obtained good balance: stacking capacity, impact resisance at low temperatures and stress cracking resistance.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Features 
  • Copolymer
  • High Density
  • High ESCR (Stress Crack Resist.)
  • High Molecular Weight
  • Low Temperature Impact Resistance
Uses 
  • Containers
  • Engineering Parts
  • Liners
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Blow Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/21.6 kg)
g/10 min
 ASTM D1238
Environmental Stress-Cracking Resistance (122°F, 10% Igepal, Compression Molded, F50)
hr
 ASTM D1693
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
     ASTM D638
Yield, Compression Molded
psi
  
Break, Compression Molded
psi
  
Flexural Modulus (Compression Molded)
psi
 ASTM D790A
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F, Compression Molded)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D, Compression Molded)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (66 psi, Unannealed, Compression Molded)
°F
 ASTM D648
Vicat Softening Temperature
°F
 ASTM D1525
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Braskem PE BT-100K, Braskem PE BT100K, Braskem PE , BraskemPEBT100K, BraskemPE, PEBT 100 K, BT, PEBT-100K, PEBT100K, PEBT:100K, PEBT/100K, PEBT+100K, PEBT_100K, PEBT 100K, PEBT100, PEBT, BT 100 K, BT-100K, BT100K, BT:100K, BT/100K, BT+100K, BT_100K, BT 100K, BT100, 100K, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, Braskem, PolyethyleneHighDensity, 100BT, 100PEBT
Features
Features may also be described by the following terms: High Molecular Weight, High MW, Low Temperatuer Impact Resistance, Low Temp Impact Resistance, High Environmental Stress Cracking Resistance, High ESCR, Stress Cracking Resistant, High Density, High Specific Gravity.
Uses
Uses may also be described by the following terms: Engineering Parts.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Injection Notes
Type to Extruder: those that have screws with minimum L/D equal to 24
Temperature profile zone 1, Blow molding: 160 to 180°C
Mold temperature, Blow molding: 5 to 25°C
Extruder temperature, Blow molding: 170 to 190°C
Die Temperature, Blow molding: 180 to 220°C
Blow up ratio, Blow molding: 3 to 4.5:1
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.