IDES Prospector Already have an account? Login Here

IDES

Adell Polyamide BH-38

Polyamide 6

Mineral Filler, 40%

Supplied by Adell Plastics, Inc.

The technical datasheet with complete property values for Adell Polyamide BH-38 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Mineral Filler, 40% Filler by Weight
Automotive Specifications 
 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Compressive Strength
psi
 ASTM D695
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F, 0.125 in)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness
     ASTM D785
M-Scale
 
  
R-Scale
 
  
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
Melting Temperature
°F
  
Additional Information
Elongation at Break, ASTM D638: 10 to 15%
Specific Gravity, ASTM D792: 1.47 to 1.49
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Adell Polyamide BH-38, Adell Polyamide BH38, Adell Polyamide , AdellPolyamideBH38, AdellPolyamide, BH, PolyamideBH-38, PolyamideBH38, PolyamideBH:38, PolyamideBH/38, PolyamideBH+38, PolyamideBH_38, PolyamideBH 38, PolyamideBH, BH-38, BH38, BH:38, BH/38, BH+38, BH_38, BH 38, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, Adell, Polyamide6, Nylon6, 38BH, 38PolyamideBH
Generic Name
Generic Name may also be described by the following terms: PA6.
Automotive Specifications
This plastic material has approval for 2 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): GM (2).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Regrind
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.