IDES Prospector Already have an account? Login Here

IDES

ATTANE™ SL 4100G

Ultra Low Density Polyethylene Resin

Supplied by The Dow Chemical Company

The technical datasheet with complete property values for ATTANE™ SL 4100G is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
ATTANE™ SL 4100G Ultra Low Density Polyethylene Resin is designed for the production of blown film requiring a combination of excellent optical properties, outstanding tear and impact strength, and very good sealability. The product also offers very good flex crack resistance.

Complies with:
  • EU, No 10/2011
  • U.S. FDA 21 CFR 176.170(c)
  • U.S. FDA FCN 424
Consult the regulations for complete details.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Agency Ratings 
  •  1
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity 3
 
 ASTM D792
Melt Mass-Flow Rate (MFR) 3 (190°C/2.16 kg)
g/10 min
 ISO 1133
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Modulus
     ISO 527-3
2% Secant, MD: 1.6 mil
psi
  
2% Secant, TD: 1.6 mil
psi
  
Tensile Stress
     ISO 527-3
MD: Yield, 1.6 mil
psi
  
TD: Yield, 1.6 mil
psi
  
MD: Break, 1.6 mil
psi
  
TD: Break, 1.6 mil
psi
  
Tensile Elongation
     ISO 527-3
MD: Break, 1.6 mil
%
  
TD: Break, 1.6 mil
%
  
Dart Drop Impact (1.6 mil)
g
 ISO 7765-1/B
Elmendorf Tear Strength
     ASTM D1922
MD: 1.6 mil
g
  
TD: 1.6 mil
g
  
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature 3
°F
 ASTM D1525
Melting Temperature 3
°F
 DSC
Optical
Nominal Value
Unit
Test Method
Gloss (20°, 1.57 mil)
 
 ASTM D2457
Haze (1.57 mil)
%
 ISO 14782
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: ATTANE™ SL 4100G, ATTANE SL 4100G, ATTANE™ , ATTANE, ATTANESL4100G, SL 4100 G, SL 4100G, SL4100, 4100G, SL4100G, Polyethylene, Ultra Low Density, Polyethylene Ultra Low Density, ULDPE, Polyethylene, PE, Dow, PolyethyleneUltraLowDensity, 4100SL
Agency Ratings
This plastic material has 3 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1), FDA (2).
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Extrusion Notes
Fabrication Conditions for Blown Film Extrusion:
  • Die Gap 1.6 to 2.5 mm
  • Melt Temperature: 190 to 240°C (Ideal: 215-225°C)
  • Blow-Up Ratio: 1.5 to 3.5
  • Recommended Gauge Range: 10 to 80 µm
Notes
1Conditions of Use A through H
2Typical properties: these are not to be construed as specifications.
3Compression moulded samples
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.