IDES Prospector Already have an account? Login Here

IDES

RheTech Thermoplastic Polyolefin FT3080-47UV

Polyolefin

Supplied by RheTech, Inc.

The technical datasheet with complete property values for RheTech Thermoplastic Polyolefin FT3080-47UV is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Thermoplastic Polyolefin, 110K Flexural Modulus, UV Stabilized, AYNA Light Prairie Tan
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Additive 
  • UV Stabilizer
Features 
  • Good UV Resistance
Automotive Specifications 
Appearance 
  • Tan
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2
psi
 ASTM D638
Flexural Modulus - Tangent
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
 ASTM D256
Gardner Impact
in·lb
 ASTM D5420
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
Additional Information
Nominal Value
Unit
Test Method
Reinforcement Content
%
 ASTM D5630
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: RheTech Thermoplastic Polyolefin FT3080-47UV, RheTech Thermoplastic Polyolefin FT308047UV, RheTech Thermoplastic Polyolefin , RheTechThermoplasticPolyolefinFT308047UV, RheTechThermoplasticPolyolefin, FT 3080, PolyolefinFT 3080 47 UV, PolyolefinFT 3080, PolyolefinFT3080-47UV, PolyolefinFT308047UV, PolyolefinFT3080:47UV, PolyolefinFT3080/47UV, PolyolefinFT3080+47UV, PolyolefinFT3080_47UV, PolyolefinFT3080 47UV, PolyolefinFT3080, FT 3080 47 UV, FT3080-47UV, FT308047UV, FT3080:47UV, FT3080/47UV, FT3080+47UV, FT3080_47UV, FT3080 47UV, FT3080, 308047, 47UV, Polyolefin, Unspecified, Polyolefin Unspecified, Polyolefin, RheTech, PolyolefinUnspecified, 3080FT, 3080PolyolefinFT
Features
Features may also be described by the following terms: Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
Automotive Specifications
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Holding Pressure
psi
  
Back Pressure
psi
  
Clamp Tonnage
tons/in²
  
Injection Notes
Cycle Time: Wall Thickness Dependent
Drying is Optional
Injection Speed: Variable - Application Dependent
Screw recovery 3 seconds before mold opens
Notes
1Typical properties: these are not to be construed as specifications.
22.0 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.