IDES Prospector Already have an account? Login Here

IDES

Flexathene® TP39NC01

Polyolefin

Supplied by LyondellBasell Industries

The technical datasheet with complete property values for Flexathene® TP39NC01 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
FLEXATHENE TP 39NC01 is an extrusion grade TPO with medium stiffness and high impact resistance, especially at cold temperatures. TP 39NC01 has very good melt strength making it a good choice for thermoforming and blow molding. This product provides a balance of high impact resistance, stiffness, and melt strength.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Good Melt Strength
  • Good Stiffness
  • High Impact Resistance
  • Low Temperature Impact Resistance
  
Uses 
  • Sheet
Forms 
  • Pellets
Processing Method 
  • Blow Molding
  • Extrusion
  • Thermoforming
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Flexural Modulus - 1% Secant 2
psi
 ASTM D790B
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
     ASTM D256
0°F
ft·lb/in
  
73°F
 
  
Unnotched Izod Impact (0°F)
 
 ASTM D256
Instrumented Dart Impact 3 (-22°F, Total Energy)
in·lb
 ASTM D3763
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (66 psi, Unannealed)
°F
 ASTM D648
Additional Information
Multi-axial Impact at Max load, ASTM D3763, -30°C, 2.2 m/s: 790 lbs
Related Terminology
This supplier and product may also be known by these terms: LyondellBasell Industries, Lyondell, Basell, Bassell, Basell Polyolefins, Bassel

Product names can be difficult to match. You may have searched any one of these terms to find this product: Flexathene® TP39NC01, Flexathene TP39NC01, Flexathene® , Flexathene, FlexatheneTP39NC01, TP 39 NC 01, TP39NC01, TP39, 39NC, NC01, Polyolefin, Unspecified, Polyolefin Unspecified, Polyolefin, LyondellBasell, PolyolefinUnspecified, 39TP
Features
Features may also be described by the following terms: Good Stiffness, Good Melt Strength, Low Temperatuer Impact Resistance, Low Temp Impact Resistance, High Impact Resistance.
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Extrusion Notes
Blow Molding Melt Temperature: 380 to 420°F (193 to 216°C)
Notes
1Typical properties: these are not to be construed as specifications.
20.050 in/min
37.22 ft/sec
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.