IDES Prospector Already have an account? Login Here

IDES

THERMOLAST® K TF2ATL (Series: FD/tl)

Thermoplastic Elastomer

Supplied by KRAIBURG TPE Corporation

The technical datasheet with complete property values for THERMOLAST® K TF2ATL (Series: FD/tl) is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • North America
Agency Ratings 
Appearance 
  • Translucent
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Molding Shrinkage - Flow 2 (0.0787 in, Injection Molded)
in/in
  
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress (Break)
psi
 ISO 37
Tensile Elongation (Break)
%
 ISO 37
Tear Strength 3
lbf/in
 ISO 34-1
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore A)
 
 ISO 868
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: THERMOLAST® K TF2ATL, THERMOLAST K TF2ATL, THERMOLAST® K TF2ATL (Series: FD/tl), THERMOLAST K TF2ATL Series FDtl, THERMOLAST® K , THERMOLAST K, THERMOLASTKTF2ATLSeriesFDtl, THERMOLASTK, TF 2 ATL, TF 2 ATL Series, KTF2ATL, KTF 2 ATL Series FD tl, KTF 2 ATL, KTF 2 ATL Series, TF2ATL (Series, TF2ATL Series, KTF2ATL (Series: FD/tl), KTF2ATL Series FDtl, KTF2ATL (Series/ FD/tl), KTF2ATL (Series+ FD/tl), KTF2ATL (Series- FD/tl), KTF2ATL (Series_ FD/tl), KTF2ATL (Series FD/tl), KTF2ATL (Series: FD:tl), KTF2ATL (Series: FD+tl), KTF2ATL (Series: FD-tl), KTF2ATL (Series: FD_tl), KTF2ATL (Series: FD tl), KTF2, KTF2ATL (Series, KTF2ATL Series, TF2ATL, TF 2 ATL Series FD tl, TF2ATLSeries, KTF2ATLSeriesFDtl, KTF2ATL Series_ FDtl, KTF2ATL Series FD_tl, KTF2ATL Series FD tl, KTF2ATLSeries, TF2ATL (Series: FD/tl), TF2ATL Series FDtl, TF2ATL (Series/ FD/tl), TF2ATL (Series+ FD/tl), TF2ATL (Series- FD/tl), TF2ATL (Series_ FD/tl), TF2ATL (Series FD/tl), TF2ATL (Series: FD:tl), TF2ATL (Series: FD+tl), TF2ATL (Series: FD-tl), TF2ATL (Series: FD_tl), TF2ATL (Series: FD tl), TF2, 2ATL, ATLSeries, SeriesFD, FDtl, KTF2ATLSeries_FDtl, KTF2ATLSeriesFD_tl, TF2ATLSeriesFDtl, TF2ATL Series_ FDtl, TF2ATL Series FD_tl, TF2ATL Series FD tl, TF2ATLSeries_FDtl, TF2ATLSeriesFD_tl, Thermoplastic Elastomer, TPE, Kraiburg TPE, ThermoplasticElastomer, 2TF, 2KTF
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): ISO (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Back Pressure
psi
  
Injection Notes
Hot Runner Temperature: 200 to 250°C
Notes
1Typical properties: these are not to be construed as specifications.
2125x125x2 mm plaque, center gate
3Method Bb, Angle (Nicked)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.