IDES Prospector Already have an account? Login Here

IDES

Alastian PE LD2-2

Low Density Polyethylene

Supplied by Alastian

The technical datasheet with complete property values for Alastian PE LD2-2 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  
Features 
  • Good Processability
  • Opticals
  
Uses 
  • Bags
  • Film
  
Forms 
  • Pellets
Processing Method 
  • Blown Film
  • Cast Film
  
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress (Yield)
psi
 ISO 527-2
Coefficient of Friction
 
 ISO 8295
Films
Nominal Value
Unit
Test Method
Film Thickness - Recommended / Available
 
  
Tensile Strength
     ISO 527-3
MD: 2.0 mil, Blown Film
psi
  
TD: 2.0 mil, Blown Film
psi
  
Tensile Elongation
     ISO 527-3
MD: Break, 2.0 mil, Blown Film
%
  
TD: Break, 2.0 mil, Blown Film
%
  
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore D)
 
 ISO 868
Ball Indentation Hardness (H 49/30)
psi
 ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/A50
Melting Temperature (DSC)
°F
 ISO 3146
Additional Information
Nominal Value
Unit
Test Method
Failure Energy (2.0 mil)
ft·lb/in
 DIN 53373
Film properties tested using 50 µm thickness blown film extruded at a melt temperature of 180°C and a blow-up ratio of 2:1.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Alastian PE LD2-2, Alastian PE LD22, Alastian PE , AlastianPELD22, AlastianPE, LD 2, PELD 2 2, PELD 2, PELD2-2, PELD22, PELD2:2, PELD2/2, PELD2+2, PELD2_2, PELD2 2, PELD2, LD 2 2, LD2-2, LD22, LD2:2, LD2/2, LD2+2, LD2_2, LD2 2, LD2, 22, Polyethylene, Low Density, Polyethylene Low Density, LDPE, Polyethylene, PE, Alastian, PolyethyleneLowDensity, 2LD, 2PELD
Features
Features may also be described by the following terms: Good Processability, Easy Processing.
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.