IDES Prospector Already have an account? Login Here

IDES

Elastron® G 527.902 SIYAH 75 SHORE A

Styrene Ethylene Butylene Styrene Block Copolymer

Supplied by Elastron Kimya A.S.

The technical datasheet with complete property values for Elastron® G 527.902 SIYAH 75 SHORE A is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  
Recycled Content 
  • Yes, 100%
Features 
  • Electrically Conductive
  • Flame Retardant
  • Good Abrasion Resistance
  • Good Chemical Resistance
  • Good Colorability
  • Good Tear Strength
  • Good UV Resistance
  • High Heat Resistance
  • Low Temperature Flexibility
  • Oil Resistant
  • Ozone Resistant
  • Recyclable Material
  • Solvent Resistant
Uses 
  • Appliances
  • Automotive Bumper
  • Automotive Exterior Parts
  • Automotive Exterior Trim
  • Automotive Interior Parts
  • Belts/Belt Repair
  • Cable Jacketing
  • Electrical/Electronic Applications
  • Electronic Insulation
  • Footwear
  • Gaskets
  • Household Goods
  • Medical/Healthcare Applications
  • Piping
  • Power/Other Tools
  • Reinforced Panels
  • Seals
  • Sporting Goods
  • Toys
Forms 
  • Pellets
Processing Method 
  • Coextrusion
  • Extrusion
  • Injection Molding
  • Pipe Extrusion
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Elastomers
Nominal Value
Unit
Test Method
Tensile Strength (Break)
psi
 ASTM D412
Tensile Elongation (Break)
%
 ASTM D412
Tear Strength
lbf/in
 ASTM D624
Compression Set
     ASTM D395
73°F, 24.0 hr
%
  
158°F, 24.0 hr
%
  
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A, Injection Molded)
 
 ASTM D2240
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Elastron® G 527.902 SIYAH 75 SHORE A, Elastron G 527902 SIYAH 75 SHORE A, Elastron® G , Elastron G, ElastronG527902SIYAH75SHOREA, ElastronG, G 527 902 SIYAH 75 SHORE A, G527.902 SIYAH 75 SHORE A, G527902 SIYAH 75 SHORE A, G527, 527 902 SIYAH 75 SHORE A, G527902SIYAH75SHOREA, 527.902 SIYAH 75 SHORE A, 527902 SIYAH 75 SHORE A, 527902, 902SIYAH, SIYAH75, 75SHORE, SHOREA, 527902SIYAH75SHOREA, Styrene Ethylene Butylene Styrene Block Copolymer, SEBS, Thermoplastic Elastomer, TPE, Elastron, StyreneEthyleneButyleneStyreneBlockCopolymer, ThermoplasticElastomer, 902527, 527G
Features
Features may also be described by the following terms: Low Temperature Flexibility, High Heat Resistance, Electrically Conductive, Conducts Electricity, Conductive, Good Abrasion Resistance, Abrasion Resistant, Good Tear Strength, Good Chemical Resistance, Chemical Resistant, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant, Good Colorability.
Uses
Uses may also be described by the following terms: Gaskets, Gasketing, Household Goods, Housewares, Piping, Pipe, Belts/Belt Repair, Belt Repair, Reinforced Panels, Reinforced Panel, Automotive Bumper, Automotive Bumpers, Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector, Electronic Insulation, Power Tools, Tools, Medical Applications.
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Injection Notes
Shrinkage: 1 to 3%
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Melt Temperature
°F
  
Die Temperature
°F
  
Extrusion Notes
L/D Ratio: 20 to 24:1
Compression Ratio: 2.5 to 3.5
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.