IDES Prospector Already have an account? Login Here

IDES

Daplen™ ED230HP

Polypropylene

Mineral Filler, 20%

Supplied by Borealis AG

The technical datasheet with complete property values for Daplen™ ED230HP is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Daplen ED230HP is a 20% mineral filled elastomer modified polypropylene compound intended for injection moulding.

This material has excellent balanced mechanical properties and gives a good surface quality.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  
Filler / Reinforcement 
  • Mineral Filler, 20% Filler by Weight
Features 
  • Good Surface Finish
  • Paintable
  
Uses 
  • Automotive Exterior Parts
Automotive Specifications 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ISO 1133
Molding Shrinkage
     Internal Method
-- 2
%
  
194°F, 2 hr
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1
Tensile Stress (Yield)
psi
 ISO 527-2/50
Tensile Strain
     ISO 527-2/50
Yield
%
  
Break
%
  
Flexural Modulus 3
psi
 ISO 178
Flexural Strength
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-22°F
ft·lb/in²
  
-4°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
     ISO 179/1eU
-4°F
ft·lb/in²
  
73°F
 
  
Notched Izod Impact Strength
     ISO 180/1A
-4°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Hardness
Nominal Value
Unit
Test Method
Ball Indentation Hardness (H 132/10)
psi
 ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Vicat Softening Temperature
      
--
°F
 ISO 306/A50
--
°F
 ISO 306/B50
CLTE - Flow (-22 to 176°F)
in/in/°F
 Internal Method
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Daplen™ ED230HP, Daplen ED230HP, Daplen™ , Daplen, DaplenED230HP, ED 230 HP, ED230HP, ED230, 230HP, Polypropylene, Unspecified, Polypropylene Unspecified, PP, Unspecified, PP Unspecified, Polypropylene, PP, Borealis, PolypropyleneUnspecified, PPUnspecified, 230ED
Generic Name
Generic Name may also be described by the following terms: Polypropilene, Polypropelene.
Features
Features may also be described by the following terms: Good Surface Finish.
Automotive Specifications
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): PSA Peugeot-Citroën (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Hopper Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Holding Pressure
psi
  
Injection Notes
Back pressure: Low to medium
Screw speed: Low to medium
Flow front speed: 100 - 200 mm/s
Notes
1Typical properties: these are not to be construed as specifications.
2disk
30.079 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.