IDES Prospector Already have an account? Login Here

IDES

Plenco 01510 (Transfer)

Thermoset Polyester

Supplied by Plastics Engineering Co.

The technical datasheet with complete property values for Plenco 01510 (Transfer) is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
PLENCO 01510 is a mineral filled, pelletized polyester molding compound, which offers an excellent combination of electrical properties and dimensional stability. UL recognized under component file E40654. 01510 is available in black.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Good Dimensional Stability
  • Good Electrical Properties
  
Appearance 
  • Black
Forms 
  • Granules
Processing Method 
  • Resin Transfer Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Apparent Density
g/cm³
 ASTM D1895
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Compressive Strength
psi
 ASTM D695
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
ft·lb/in
 ASTM D256
Notched Izod Impact
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (E-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
Max. Continuous Use Temperature
°F
 ASTM D794
CLTE - Flow
in/in/°F
 ASTM E831
Thermal Conductivity (212°F)
Btu·in/hr/ft²/°F
 ASTM C177
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength     ASTM D149
-- 2
V/mil
  
-- 3
V/mil
  
Dielectric Constant (1 MHz)
 
 ASTM D150
Dissipation Factor (1 MHz)
 
 ASTM D150
Arc Resistance
sec
 ASTM D495
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0591 in)
 
 UL 94
Oxygen Index
%
 ASTM D2863
UL File Number
 
  
UL
Nominal Value
Unit
Test Method
Comparative Tracking Index (CTI)
V
 UL 746
Additional Information
The value listed as Mold Shrink, Linear-Flow, ASTM D955 was tested according to the ASTM D6289 standard.
The value listed as Comparative Tracking Index, UL 746 was tested according to ASTM D3638.
The value listed as Thermal Conductivity, ASTM C177 was tested according to the ASTM E1461 standard.
Post Shrinkage, ASTM D6289, 72hr, 120°C: 0.01%
Heat Resistance, ASTM D794: 213°C
Drop Ball Impact, PLENCO Method: 119 J/m
Related Terminology
This supplier and product may also be known by these terms: Plenco

Product names can be difficult to match. You may have searched any one of these terms to find this product: Plenco 01510, Plenco 01510 (Transfer), Plenco 01510 Transfer, Plenco , Plenco01510Transfer, 01510, 01510 (Transfer), 01510 Transfer, 01510Transfer, Polyester, Thermoset, Polyester Thermoset, Polyester, TS, Polyester TS, Thermoset, TS, Plastics Eng, PolyesterThermoset, PolyesterTS, Transfer01510
Features
Features may also be described by the following terms: Good Electrical Properties, Good Dimensional Stability, Dimensionally Stable.
Injection
Nominal Value
Unit
 
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Injection Notes
Transfer Time: 3-8 sec
Transfer Pressure: 5.5-6.9 MPa
Preheating Temperature: 93-100°C
Notes
1Typical properties: these are not to be construed as specifications.
2Method A (Short-Time)
3Method B (Step-by-Step)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.